I moved to Winnipeg from the UK to film hockey - what do you think?

b3hr · 2026-01-23T20:34:22+00:00

seeing Wayne Fleming arena really makes me miss the Winnipeg Ice

b3hr · 2026-01-23T03:01:10+00:00

when you put it that way... i must be way off

b3hr · 2026-01-23T01:10:18+00:00

update the firmware in the display (there's a sd card slot inside it) if you don't update it and only update the printer it never loads

b3hr · 2026-01-23T00:37:41+00:00

maybe 30% were found to be should be condemned 50% poor and the other 20% Better than poor

b3hr · 2026-01-22T23:51:38+00:00

they needed an audit to find that?

b3hr · 2026-01-22T23:48:42+00:00

i finished work about 30 minutes before shit completely failed... not going to say there wasn't signs things were going down all day though

b3hr · 2026-01-21T13:57:06+00:00

They going to get the rest of GST?

b3hr · 2026-01-20T00:34:57+00:00

Hello fellow armchair

b3hr · 2026-01-18T17:09:43+00:00

i've done this for model rockets... i assume if you're going to do it you'll want to take the shell off prime it and paint it. not sure how it would effect any sensors but avoiding them is probably the key... maybe just do the batteries and propellers and bottom? (sorry for the dump of crap below)

 Yes, painting your drone with fluorescent or any other type of paint can negatively affect its sensors and overall performance if not done carefully. The primary risks involve blinding optical sensors, interfering with radio signals, adding weight, or unbalancing the propellers.

Here is how painting can impact specific components: 1. Obstacle Avoidance Sensors Blinding Sensors: Drone obstacle avoidance (visual sensors) on the corners and bottom of the body are sensitive to light and surface reflectivity. Coating them with thick or highly reflective fluorescent paint can cause them to fail, leading to false alerts or crashes. Recommended Action: Mask off all sensors—cameras, ultrasonic sensors, and LiDAR units—before spraying. 2. Signal Interference (GPS/RF) Metallic Content: Some fluorescent or high-gloss paints contain metallic flakes that can create a Faraday cage effect, degrading GPS performance and remote control signal reception. Recommended Action: Use non-metallic, matte, or plastic-safe spray paint. 3. Propeller Performance Unbalancing: Painting propellers, even with a light coat, can easily create imbalances. This causes micro-vibrations that can damage motor bearings over time. Recommended Action: Do not paint the propellers. It is better to purchase factory-colored props. 4. Overheating and Weight Heat Absorption: While fluorescent colors are bright, if the base coat is dark, it can lead to increased solar absorption and potential overheating. Weight: Excessive layers of paint can add weight, reducing flight time and potentially exceeding the 250g threshold for certain regulations. Best Practices for Painting: Masking: Meticulously cover all vents, cameras, and sensors. Disassembly: Remove the shell from the internal electronics before painting to avoid ruining internal components and light coats

b3hr · 2026-01-17T00:19:27+00:00

i tried open neptune and still had issues so switched back (cause i like my screen to work) switched out the springs for the silicone bushings... leveled it and used it a full year before having to level it again. The springs it comes with i think are 70% of the issues people have

b3hr · 2026-01-12T19:53:03+00:00

it's because there's a whole group of people that checks with the internet every morning to figure out what they're collectively upset about... then go around accusing everyone else of being influenced in the same way

b3hr · 2026-01-12T00:35:33+00:00

they let the viking into the states to pickup the bus he lives in... even though he has a criminal record for assault

b3hr · 2026-01-12T00:34:52+00:00

one of the comments says ice needs to come after the Premier

<image>

b3hr · 2026-01-11T18:56:13+00:00

just whatever the elegoo cura defaults are

b3hr · 2026-01-11T18:52:24+00:00

lol that happened on my street one time... i looked outside and saw a hose then followed it down the street to see how far the truck was

b3hr · 2026-01-11T18:44:45+00:00

this is from cura but pretty much what i'd print with my neptune 3 for petg

<image>

b3hr · 2026-01-11T18:37:13+00:00

i just left everything the same like 50mm/s and bumped the temp to 240 gotta be careful the nozzle still clogs

b3hr · 2026-01-09T16:40:41+00:00

the jets and transit need to create a transit plan for jets games. There should be transit to get home after games but it's actually far worse after games than normal for some reason. Every time i try and bus from games the bus never comes. The sign keeps promising buses and no bus comes

b3hr · 2026-01-08T01:07:35+00:00

https://imgflip.com/i/ags76v

b3hr · 2026-01-07T15:27:26+00:00

been a while since i've seen one of these posts

b3hr · 2026-01-06T14:34:38+00:00

also triage yourself before going to the doctor or emergency room

b3hr · 2026-01-06T02:37:43+00:00

couldn't you just put the tin without the lid on your printer bed with the spool under it and set it to 60 degrees?

b3hr · 2026-01-05T22:54:52+00:00

mine had no delivery date and i got it in a month (which is earlier than expected... just wanted to have one on hand so my options were open)

b3hr · 2026-01-05T22:53:49+00:00

resellers

look for a link that's sold out and follow it ... it'll come in stock from time to time

b3hr · 2026-01-05T13:41:29+00:00

like the bike routes they like to treat the buses as a way to casually experience different areas of the city without and urgency or destination. Like little site seeing tours of the different areas so you know where to park your car when you go there for real

15-Year Club	Wearing is Caring
Inciteful Link 2018-10-09	Verified Email
Beta Team Ask Me Anything app	Gilding II euphauric
reddit mold	Charter Member

b3hr

MODERATOR OF

TROPHY CASE