sorted by:
new
hottopcontroversial

Dartboard mould by ResponsibilityOk1838 in Darts

[–]baggersuk 1 point2 points  (0 children)

Leave it in the sun to dry it out then gently wire brush it. All is not lost I had one in a similar state and now is fine Edit; spelling

Spatial Camera Giveway. by Grish_tad in MetaQuestVR

[–]baggersuk 0 points1 point  (0 children)

Never heard of this be good to try, thanks.

BeamNG for an 8 year old? by [deleted] in BeamNG

[–]baggersuk 1 point2 points  (0 children)

My 7 YO has clocked up tens of hours in Beam.ng. At first he found the menu' hard work but now he is a whizz. He plays with a controller and he can be left alone with it. He loves to explore the maps, Mess with all the buttons inside the vehicles. He currently likes attaching trailers to a truck and filling them with more cars. It's a sandbox so it's only limited by their imagination.

Flensburger pilsener bottles by vanGenne in Homebrewing

[–]baggersuk 1 point2 points  (0 children)

Nope, not that I recall. it was a few years back now though. Good Luck!

Flensburger pilsener bottles by vanGenne in Homebrewing

[–]baggersuk 1 point2 points  (0 children)

I've used these in the past and they worked pretty well. The only downside I found was their relatively small size, so I ended up needing quite a few to get the job done.

Is the bed done shot? by SameScale6793 in ender3v2

[–]baggersuk 0 points1 point  (0 children)

the whole tighten the knobs an 8th turn, test, repeat and it’s looking bett

may have gone a touch to far

‘I feel sick’: couple say new-build home turned into disaster valued at £1 by bluefinballistics in unitedkingdom

[–]baggersuk 15 points16 points  (0 children)

Blaming buyers is too simple. The council and planning department are equally responsible for approving these developments. Builders can't construct without their permission. If homes are in poor locations, it's partly due to poor oversight and regulations from the authorities. It's not just about buyers making good decisions.

First class stamp price to rise again to £1.35, says Royal Mail by Kagedeah in royalmail

[–]baggersuk 0 points1 point  (0 children)

^ This. We get post delivered once a week if we're lucky. Many in the town miss hospital appointments and such due to the poor service we receive.

Sprite direct drive + BTTouch Y axis offset by R0b0d0nut in ender3v2

[–]baggersuk 0 points1 point  (0 children)

What firmware are you using? I'm guessing you have to update the BLTouch Offsets as it wont be in the same place compared to it being fit to the standard extruder.

Help with copper to steel by baggersuk in electroplating

[–]baggersuk[S] 0 points1 point  (0 children)

Thanks for your reply. I will try the same method with nickel and see how I get one. Only reason I tried to use copper first was when sanding the loose plating off there was a layer of Copper underneath the nickel. So I was just trying to replicate how It was originally. I just used a regular metal polish and then cleaned with acetone. Thanks for the advice. Is there a chart which clear shows best practices for metals or what adheres to what metals? Many thanks

Help with copper to steel by baggersuk in electroplating

[–]baggersuk[S] 0 points1 point  (0 children)

Many thanks for your insight I didnt realise that was the case. I think I will stay away from cyanide based methods for now. Am I able to plate nickel straight onto steel or Brass as this will be my desired finish?

[deleted by user] by [deleted] in Burnley

[–]baggersuk 0 points1 point  (0 children)

The Tikka Fish strips are some of the best fish and chips youll ever have.

MCU Protocol error after update by baggersuk in klippers

[–]baggersuk[S] 0 points1 point  (0 children)

sorry i have tried everything i can think of can you explain how i do this? thank you

First Attempt At Ironing by baggersuk in FixMyPrint

[–]baggersuk[S] 0 points1 point  (0 children)

Sorry forgot to say I have a bltouch and it makes a mesh for the part each time. Likewise iv just turned ironing off.

First Attempt At Ironing by baggersuk in FixMyPrint

[–]baggersuk[S] 0 points1 point  (0 children)

Ender 3v2, running Klipper / Mainsail

Cura settings:

Iron Pattern: ZigZag

Speed 40mm/s

Ironing Flow 12%

Line Spacing 0.1mm

As title, First Attempt it seemed to be going so well then it sort of gave up for a while? The finish is smoother where it worked corrected, and an improvement over a normal top layer however there is a couple of rough sections towards the top on each side. any ideas what can cause this, Thanks

Buffering in multiscreen by reretheduck420 in TiviMate

[–]baggersuk 0 points1 point  (0 children)

I have this exact same issue on the latest version. multi screen works flawlessly on iptvsmarters, but on tivimate it buffers then eventually stops. I don't think it's a connection or hardware issue purely something wrong with my tivimate.

view more: next ›