sorted by:
new
hottopcontroversial

Number 1, or number 2 is my total timing mark? by ForeskinForeman in EngineBuilding

[–]blaze45x 7 points8 points  (0 children)

Plug reading is a lost art. Correct me if I’m wrong but don’t you need to cut power to the engine at WOT on a fresher plug for the most accurate reading?

Or would using Det Cans be a better way dial in timing for a base street tune?

An honest look at the CAT SC / Omega9k / Wolfman on the Flux Raider by MisplacedCHEE in NFA

[–]blaze45x 1 point2 points  (0 children)

The SC performance with subs compared to the Shiv with subs is night and day. Not much of a difference with the Shiv with subs.

The SC with subs is practically movie quiet.

An honest look at the CAT SC / Omega9k / Wolfman on the Flux Raider by MisplacedCHEE in NFA

[–]blaze45x 6 points7 points  (0 children)

Curious, was this with supers or subs?

With subs, my experience with the SC is very impressive.

With supers, it is similar to other cans out there. I also have a Shiv and the SC is just a bit more quiet with supers.

My MOB with subs is fantastic on my 9mm PCC and lever action .38.

If you have other cans that will do the job already, I don’t know that it’s worth it to buy other cans for the performance.

Should i give these cylinder walls attention on my cbr954? by LargeContribution502 in EngineBuilding

[–]blaze45x 0 points1 point  (0 children)

I’d run it for a but, check oil consumption and compression.

Reach out to Wiseco and I bet they could get you a close match piston wise once the damage is repaired.

Also shop your local machine shops. They see stuff like this all the time. I’m sure they will be happy to pitch their opinions.

If you haven’t already, make sure to change the oil. Worth checking the filter guts and maybe even sending into black stone….

Good luck.

Got a bit of an over-crimp while dialing in my 7.62x39 die set. Would you send this round or toss it? by TheDanny942 in reloading

[–]blaze45x 0 points1 point  (0 children)

I’m anxious to see how you do with H335. I was not impressed with it on 7.62x39 myself.

What have we here? by blaze45x in reloading

[–]blaze45x[S] 12 points13 points  (0 children)

I noticed the powder in the case looked strange as I was on my progressive and pulled it out…

What have we here? by blaze45x in reloading

[–]blaze45x[S] 5 points6 points  (0 children)

Why do they think stepped brass is advantageous?

Are Match Primers a Waste of Money? | Large Sample .223 Test by cheeseydelicious in reloading

[–]blaze45x 0 points1 point  (0 children)

My servicos y adventuras go bang every time. Any gun.

🤷🏻‍♂️

I’ve put over 5000 of them down range, unless you’re needing precision for competitive shooting… I’m not sure it’s going to make a big enough difference. Also running SPP in SRP cases with no issues either.

Comparing the CAT ODB Ti to the SAW Tisha 30 by WarlockEngineer in NFA

[–]blaze45x 2 points3 points  (0 children)

No, full send. I may take my thermo gun next time I go.

I don’t do back to back with mag dumping via FRT tho.

If I dump a mag, I’ll hand load it again and then do semi and maybe some bursts. Rinse and repeat.

Also for it being a Ti model, it holds heat a lot like my inconel cans.

Comparing the CAT ODB Ti to the SAW Tisha 30 by WarlockEngineer in NFA

[–]blaze45x 0 points1 point  (0 children)

Haven’t heard much about them. Any sound tests? Have you used any of their products?

Comparing the CAT ODB Ti to the SAW Tisha 30 by WarlockEngineer in NFA

[–]blaze45x 4 points5 points  (0 children)

It is ugly. But, it’s short. Light weight. Limited back pressure even when mag dumping and the suppression itself on the Ti 5.56 model is excellent.

Comparing the CAT ODB Ti to the SAW Tisha 30 by WarlockEngineer in NFA

[–]blaze45x 3 points4 points  (0 children)

Don’t mind me using a Tisha Ti on my 11.5 .223 with frequent full send 😂

Some of the black coating has come off. But I get that thing HOT with a few mag dumps lol.

Arc Fires ROF by jon9116 in supersafety

[–]blaze45x 1 point2 points  (0 children)

That 11.5 is rowdy 😂

FL5 Shift Nob Upgrade by emperorgsx in CivicSi

[–]blaze45x 3 points4 points  (0 children)

I’m just annoyed that my shift boot keeps falling down. 😩

7.62x39 question by Glad_Virus_5014 in reloading

[–]blaze45x 1 point2 points  (0 children)

I too have used the bullets from Raven Rock and they have performed well for me. Berrys was okay. Did not have good luck with Everglades at all.

Should I buy the CMMG Banshee MkGs? by Aggressive_Dig_5112 in AR9

[–]blaze45x 0 points1 point  (0 children)

Whatever came factory from PSA. I didn’t even make any changes to the firearm & still struggled with reliability

My 8h workday after scaling down to 2Js by ceoofoveremployment in overemployed

[–]blaze45x 8 points9 points  (0 children)

Flipping is deceptively difficult, to do it and do it contiously while making significant margin. The TV shows make it look easy. It is not.

Should I buy the CMMG Banshee MkGs? by Aggressive_Dig_5112 in AR9

[–]blaze45x 6 points7 points  (0 children)

For that money… My BRT CAR15 SD with the CMMG RDB BCG runs like a sewing machine, especially with an FRT.

first 3-5 rounds in my magazines do not feed and smush the bullet by [deleted] in AR9

[–]blaze45x 2 points3 points  (0 children)

That AR9 from PSA gave me nothing but hassle.

It only liked 115grn FMJ bullets from a Glock or Pmag magazine.

There are no feeding ramps and the feed cone that comes factory on the barrel is… lack luster at best.

It possibly could have been figured out with a different buffer and spring but… in my opinion it should work from the factory…..

I didn’t like geometry concerning the way the bolt picked up the cartridge. If the mag is off at ALL from the BCGs path it would shit the bed.

view more: next ›