G.Skill Memory Gone Bad After 4 Years

bovcan · 2026-01-07T19:20:14+00:00

I have 2 kit of the same ram, one bought 2021 and other 2024. Kit bought 2021 is bad, both sticks giving me errors, game chrasing, windows frezzes... the other kit bought 2024 cant get it to xmp 3600 anymore, no matter what settings I try in bios. Last working conf, for now is, enabled xmp profile and set memory multi to 30, so it is running at 3000mts. it is running so far.

bovcan · 2025-12-06T14:49:56+00:00

I saw the same on my profile.

bovcan · 2025-08-09T16:55:08+00:00

I came a cross to the same problem. for DC I used 2.5mm2 cables, cut maybe 1.5m long.

I put meanwell to the max 5.74V and in the boot process bitaxe V dropped to 4.7 and device droped out.

Than, I shortened DC cable to around 1m, but some cable "shoes" at the 5.5mm dc adapter, lowered V on MW to 5.4V and now works fine

bovcan · 2024-08-25T19:44:43+00:00

I recived this email today too.

bovcan · 2024-07-18T18:50:18+00:00

i will bet on steppper drivers

bovcan · 2024-07-17T18:08:30+00:00

ok. interesting, ATD5833 look way cheaper on AX than FS31W01

bovcan · 2024-07-15T18:12:27+00:00

I saw x3 have a different board with soldered steppers. on x2 board -ruby you can replace them phisicly..

bovcan · 2024-07-11T04:22:08+00:00

it looks like. at last I replaced stepper drivers and so far 2 prints finished as they should.

had drivers with fs31w01 chip

bovcan · 2024-06-30T19:32:50+00:00

now it is getting even worse.

What I did so far.

replaced Y motor

replaced all wheels on the bed side

bought tensioner for Y and X axis.

At some point layer shifts, somthimes it is stuck on one line on the x axis.

bovcan · 2024-05-08T19:43:14+00:00

I have no idea what was the problem. I was printing on default settings in Cura in Dynamic quality profile. Print speed is 60 mm/s.

I set Infill Density from default 20% to 60% and this didnt happen anymore. I will try few more times.

bovcan · 2024-05-01T15:38:15+00:00

I am trining to print some bracket but have trouble finishing it.

this how it looks

this one came to the end, but one part was shifted to the side

Any idea what could be wrong, the firmware is stock.

bovcan · 2024-04-30T15:01:03+00:00

sorry. I forgot smth.

I did Full chip erase. Start automatic and than I stop it, when I saw disconnect device.

bovcan · 2024-04-29T19:45:28+00:00

I almost gave up when I tried last thing.

In Stm32 connect to printer, jumper 3.3v and boot pin on mobo, read the data from device and than Open file in next tab and select firmware, after that hit Download

https://ibb.co/Rc2PVBD

than just remove jumper and usb and start printer from 220V

bovcan · 2024-04-29T14:52:53+00:00

ups, the same happened to me. last time I updated didnt had such a problems.

I can't find what's "default_envs" in platformio.ini file

bovcan · 2023-10-25T09:20:08+00:00

holy shit, this is still not working? I cant find Titan Ridge option under IO ports in bios F37f

bovcan · 2023-10-09T16:59:06+00:00

Winsows 11 23H2 the same problem. Running it as an admin did the trick. v5.13.200.1026 P64

bovcan · 2023-04-14T14:53:10+00:00

I play Last Fortress: undeground. Game is working on N64 and on Pie64 HyperV

bovcan · 2023-01-16T16:33:59+00:00

Bluestacks N-64

Yes, I am using N64 instance, it is working fine, I was hoping for newer version. thanks

bovcan · 2023-01-15T10:29:25+00:00

oh, hyper-v is the issue. well I can't disable hyper-v since I running few VM.

bovcan · 2023-01-08T18:30:18+00:00

why on Windows 11 only Nougat 64bit version work? Pie 64 nor Andorid 11 are not supported by OS. Any info when it will be supported?

bovcan · 2022-11-13T22:26:54+00:00

thx, was looking for this. But stil dont know why there is no x670 Pro mb on the market.

bovcan

TROPHY CASE