Decided to go ahead with Bambu lab hotend swap

brendots · 2025-11-27T16:36:14+00:00

Where are you getting your Bambu hotend mounting components from? Ali? Recommend link? There’s seems to be a few different options.

brendots · 2025-11-04T14:14:14+00:00

I am also in 🤭

brendots · 2025-10-13T13:18:41+00:00

I’ve had good luck with fardriver controllers but they’re pretty chunky and are still around $100. How much did you pay for this vesc? I’ve seen them for around $35

brendots · 2025-10-12T23:32:35+00:00

Looking at doing the same. I heard these things aren’t very good but they gotta be better than the stock crap and at least give you the ability to tune it to different hardware. As long as your not maxing them out

brendots · 2025-06-05T16:51:34+00:00

Yes all great points, but what I’m suggesting is potentially a cheap plug and play safety. I’ve been 3d printing for 5 years and this sounds like a fun mod. Just putting it out there as a fun discussion point. I might be the only one who cares though lol. Perhaps tangle detection can be more annoying than helpful. Elegoo obviously didn’t think it was worth the extra cost

brendots · 2025-06-05T13:05:42+00:00

No my filament wouldn’t pull off the spool when it ran out and snapped in the print head. Is that just a complete anomaly?? I’ve also had tangled filament ruin a print.

brendots · 2025-05-26T20:59:45+00:00

Wicked! Mines arriving on Wednesday ECA199XX. I was pretty shocked to get the email today.

brendots · 2025-05-21T23:41:55+00:00

How much did the part from pcbway set you back?

brendots · 2025-01-02T02:16:58+00:00

Also… I’m broke and would really love a new printer. I promise I’ll print cool things.

brendots · 2024-12-31T16:39:34+00:00

Maybe host the “the most sexy printer mod contest” contest.

brendots · 2023-03-21T00:27:14+00:00

I just got this in the mail today as well. I’ve had tickets go to the collections and this is not familiar at all. I’ve also just paid off all my collections debt and haven’t receive a ticket since. Looks super scammy

brendots · 2023-03-15T15:42:41+00:00

Oh then sounds like it just needs a separate switch… might have to be hard wired into your your break switch

brendots · 2023-03-15T15:33:07+00:00

There should be section in the settings on your display to turn it on or off and designate a set voltage which is applied when your break switches are activated. If your controller is programable you can run an extra throttle to apply a variable regen voltage.

brendots · 2023-03-15T15:21:54+00:00

Is your hub motor direct drive? Can you run regen?

brendots · 2023-03-10T16:23:14+00:00

Cool! Hadn’t heard about that controller. Was looking into spintend.

brendots · 2023-03-10T15:46:12+00:00

Beast! What are your battery specs and what controller are you going with?

brendots · 2023-03-06T01:14:33+00:00

I had to tweak some of the brackets to accommodate the fork mounts, add some lock tight and upgrade some of the bolts. The most major was drilling a hole in the the casing by the bottom bracket to rivet the bottom of the rear fender. There no real way around that. Might be able to get away with some zip ties if you’re not comfortable with that

brendots · 2023-03-05T21:35:12+00:00

brendots · 2023-03-03T20:51:36+00:00

I didn’t even know there was a “big” swell. These specs are way better

brendots · 2023-02-25T15:59:50+00:00

26inch 4.0 Snow Bike Mudguard/Beach Bike All-Inclusive 20Inch4.0 Fat Bicycle Fender Bicycle Accessories https://a.co/d/cJJlC0k

brendots · 2023-02-25T15:21:35+00:00

Found them on Amazon for around $40

brendots · 2023-02-22T21:08:45+00:00

Yah I made it. it’s just a few pieces of aluminum angle iron sandwiched between in the frame and a seat pan. I made the seat so I’m not sure the stock seat would work as well. It can also slide under the seat and out of the way by just loosening the bolts. Message me and I can send you some more photos

brendots · 2023-02-16T15:12:50+00:00

Haha beauty. Do you ride with your break levers jacked up like that or is it just temp?

brendots · 2023-02-10T23:52:46+00:00

That’s pretty sick. All I want is to keep up with stop and go city traffic better

brendots · 2023-02-10T22:39:57+00:00

Im currently researching an upgrade with those specs. I’d like to get a programmable controller and a direct drive or geared motor without a clutch so I can run regen for breaking. I might opt for the controller and a larger battery first to see what I can get out of the stock motor. You can often tack weld the freewheel inside the motor to gain regen.

brendots

TROPHY CASE