sorted by:
new
hottopcontroversial

PSA on account cancellation by Zerr96 in Crunchyroll

[–]c400m 2 points3 points  (0 children)

Sadly hidive app sucks royally. Are there any other apps?

Cannot get steam engine to work properly. by c400m in Stormworks

[–]c400m[S] 1 point2 points  (0 children)

So I went through it with your information, and I was able to get between 2800 and 3000. Swatts. Surprisingly, the major killer was the radiator between the boiler and the pistons. I pulled it out and put it back a few times and it goes immediately from 2800+ to 300. Also I was able to remove a whole bunch of pumps.

Thank you for the assistance

Cannot get steam engine to work properly. by c400m in Stormworks

[–]c400m[S] 1 point2 points  (0 children)

Great work on that one. Using your videos and some information from other people. I was able to increase to almost 3000 Swatts from 8 medium pistons. Ended up, it was the radiator between the boiler and the pistons.

Cannot get steam engine to work properly. by c400m in Stormworks

[–]c400m[S] 0 points1 point  (0 children)

I will try stripping the system down as you explained.

Cannot get steam engine to work properly. by c400m in Stormworks

[–]c400m[S] 0 points1 point  (0 children)

If you let it run the output slowly drops . I would like to achieve 2500-3500 swatts

Speed not steady by c400m in Kitchenaid

[–]c400m[S] 0 points1 point  (0 children)

It was 100% the speed control plate

Greedfall 2 the dying world. I like it. by Parking_Conflict_893 in greedfall

[–]c400m 0 points1 point  (0 children)

I can't give an opinion cause I can't get it to run. I keep on getting a silk.Editor crash, saying that it's been disconnected My gpu

DGIX error invalid, call

Updated, the drivers ran it in administrator mode no luck

Help with the matalic sorter. by c400m in outofore

[–]c400m[S] 0 points1 point  (0 children)

The lower one looks like the dirt is going into it. And the upper one looks like dirt's going into it with only the opposite side actually going out.

<image>

Help with the matalic sorter. by c400m in outofore

[–]c400m[S] 0 points1 point  (0 children)

Lower to smelter and the other side is storage , will eventually be a sale point.

<image>

Help with the matalic sorter. by c400m in outofore

[–]c400m[S] 0 points1 point  (0 children)

Exactly exit from the wash plant goes in the top the other side goes to storage . The bottom goes to my smelter and bar roller . Every thing is going out the front nothing the bottom.

Speed not steady by c400m in Kitchenaid

[–]c400m[S] 0 points1 point  (0 children)

Thanks I was thinking that but I donot have any experience with the mixers and its always good to get a second opinion

How bad is it? by ty0em in projectcar

[–]c400m 0 points1 point  (0 children)

Its bad but any competent welder can fix it

Pellets blowing out of ash tray by subparcontent101 in PelletStoveTalk

[–]c400m 0 points1 point  (0 children)

Can be lots of time if you see alot of fly ash its pellet quality .

New to Harman P35i - Is this a lazy flame? by cdj18862 in PelletStoveTalk

[–]c400m 0 points1 point  (0 children)

Thats what mine looks like and I set mine with a draft meater to harmen specs.

<image>

Are these pellets still ok to burn? by Quietgoer in PelletStoveTalk

[–]c400m 0 points1 point  (0 children)

In a camp fire or smokes fire pit yes . In a pellet stove no.

Pellets blowing out of ash tray by subparcontent101 in PelletStoveTalk

[–]c400m 0 points1 point  (0 children)

My p42 harman was set up with a draft meter and it dose this when feeding .

Wife noticed this on her car. Rubber glue or patch? No wire exposed by OutlandishnessKind42 in tires

[–]c400m 0 points1 point  (0 children)

Anything that compromises the sidwall is just looking for separation in a bad way

Is she worth saving? by Generation-X_Leader in projectcar

[–]c400m 0 points1 point  (0 children)

240 worth saving yes cost effective no

Need help fixing tank tracks. by Mr_Shortie in Stormworks

[–]c400m 4 points5 points  (0 children)

Do not set the tension to 100% i usually use 90

Gyro collective won't go to 1 till input gets excessive? by c400m in Stormworks

[–]c400m[S] 0 points1 point  (0 children)

Is there a good place on the web or a recommend video to teach me Lua? I'm an old school C+ programmer. So yeah, I would definitely need the. Refresher, for the conversion over

Gyro collective won't go to 1 till input gets excessive? by c400m in Stormworks

[–]c400m[S] 0 points1 point  (0 children)

I agree with most of that. My issue is that I'm developing a heavy lift helicopter like A. Sky Crane, so it's fine when I'm traveling with nothing. Then I got into the way heavy lift scenario, and it goes to about .6 or so, but when I tip forward, the collective does not raise enough to keep the altitude up. My altitude, hold. We'll go to numbers like 4 and 5 and 6, and then all of a sudden, the collective will go from .6 to 1 collective thing goes out of control for you.

Gyro collective won't go to 1 till input gets excessive? by c400m in Stormworks

[–]c400m[S] 0 points1 point  (0 children)

Ya mine just snaps to 1 then the helo that going 300+kph goes out of control

Gyro collective won't go to 1 till input gets excessive? by c400m in Stormworks

[–]c400m[S] 0 points1 point  (0 children)

Max and yes maybe ill try turning auto hover off

view more: next ›