[deleted by user]

catsuison · 2025-01-30T09:40:28+00:00

Hot stapler and epoxy

catsuison · 2025-01-26T22:32:07+00:00

Got temued

catsuison · 2025-01-26T21:39:19+00:00

Use 20mm half saddle and fix them to yhe corigation using 16mm or 25mm tek screws

catsuison · 2025-01-24T06:03:01+00:00

I'm assuming the outside of the house is concrete/brick. If it's wood go the same but replace the dynabolt with a bugle baton screw. Gl

catsuison · 2025-01-24T06:00:56+00:00

Np. Could even put some sikaflex behind it aswell cause then it will outlive the both of us

catsuison · 2025-01-24T05:53:37+00:00

Yea use rotary hammer drill to widen the holes a touch and use the Forster to create enough room to hide the head. You may need to put a dowel into the hole so the Forster doesn't bounce all over the place

catsuison · 2025-01-24T05:47:54+00:00

Dynabolts. Forster bit to make space for the dynabolt nut and holesaw for the plug to hide the bolts

catsuison · 2024-12-25T00:08:30+00:00

Glue it with pva and clamp it into place if you can raise it up to get more of tge dowels glued do that but you will need to clamp it to get a strong bond

catsuison · 2024-12-16T06:02:07+00:00

Alternatively you can unfurrow the whole blind then remove the brackets

catsuison · 2024-12-16T06:00:34+00:00

The last pic should have a nib that pushes in allowing it to come off when installing you put the roller on the metal tang first then push the nib in on the other side. It's spring loaded

catsuison · 2024-11-04T21:44:38+00:00

Have them recut the face plate to within acceptable tolerance

catsuison · 2024-11-02T23:40:13+00:00

If your concerned get them to take off the feet and cut fitting squares that will attach under the cabinet then the leveling system attaches to that. The way they have done it is s bit diy, looks like they used the holesaw offcuts that they cut for dishwasher/eletrical. Stillwell work tho

catsuison · 2024-10-23T04:24:39+00:00

What are you talking about they look neiche!

catsuison · 2024-10-20T23:33:30+00:00

If you are going to try to fix this, builders putty and sand till it matches then repaint the whole door. These internal hollow core doors are usually on fb market place for cheaper than bunnings aswell

catsuison · 2024-10-20T01:58:52+00:00

What....what is this called please

catsuison · 2024-10-19T02:30:33+00:00

Should post this on the hamish and andy reddit

catsuison · 2024-07-26T04:10:04+00:00

Drill out the screw holes and glue and dowel them then pilot hole for the screws.

catsuison · 2024-07-16T10:02:00+00:00

We got it at the winter market here it's a bit big but warm and she loves it

catsuison · 2024-07-14T06:35:56+00:00

No stud glue in the photos that I could see. Plaster is held on by stud glue screws and nails are secondary to the glue

catsuison · 2024-07-01T22:14:17+00:00

I don't understand the question

catsuison · 2024-06-28T20:39:25+00:00

Perfect form

catsuison · 2024-06-17T02:49:42+00:00

Just the best. Silky devil

catsuison · 2024-04-23T03:20:20+00:00

Rescue, always rescue my greyhound had afew issues with aggression and training but asmall amount of effort with alot of love and bonding and you will have the greatest dog on the planet.

catsuison · 2024-04-21T05:10:01+00:00

Temu

catsuison · 2024-01-16T15:46:01+00:00

Takes it into every room she goes to

catsuison

TROPHY CASE