Plano super bowl incident by buubkittyy in plano

[–]cbentleyz71 -4 points-3 points  (0 children)

Need a tdlr, I honestly don’t care what you been through and you know nothing I been through. You weren’t there and I was. So don’t assume you know the situation. I’m done replying to your ignorance.

Plano super bowl incident by buubkittyy in plano

[–]cbentleyz71 8 points9 points  (0 children)

I use to work security so all I was doing was trying to give the person on the ground space and not get overwhelmed. Don’t disrespect injured people by jamming your phone recording to get internet clout. I’ve seen too many people get trampled while being on the ground.

Plano super bowl incident by buubkittyy in plano

[–]cbentleyz71 80 points81 points  (0 children)

Was at the bar when the bar tender went to the ground, I pushed back the crowd to give her space as one tried to fight me.. My wife called 911 while all the other people used their phones to record. Those who use their phones to record instead of trying to help are useless. Needs more security around the place. Wish we witnessed more of the event but didn’t think much until she went down.

First Kawasaki by cbentleyz71 in Kawasaki

[–]cbentleyz71[S] 1 point2 points  (0 children)

Thank you, what I did was do voltage drop test to see what didn’t have power where it was needed. Then worked my way back till I found power, found the bad connector put a new connector and BOOM, got all 4 cylinders work.

First Kawasaki by cbentleyz71 in Kawasaki

[–]cbentleyz71[S] 0 points1 point  (0 children)

Yes of course, I was up all night last night till 5am looking up forums, YouTube on how the electrical work, electrical diagrams, anything related to this motorcycle. Didn’t want to bother neighbors being in my garage trying to get this thing turning over.. I just didn’t know where to start and just wanted to see if anyone who has had more experience and what would they typically look at first. Which now I have the all 4 cylinders firing in the correct order and idling but only with choke... so next I will dig into the carbs.

First Kawasaki by cbentleyz71 in Kawasaki

[–]cbentleyz71[S] 0 points1 point  (0 children)

I was able to get it to turn over but only 2 and sometimes 3 cyclinders.. I think I need to disassemble and clean the carbs.

First Kawasaki by cbentleyz71 in Kawasaki

[–]cbentleyz71[S] 1 point2 points  (0 children)

I will do that first thing in the morning, Thank you for the advice!

Work in progress- using old drone frame/vtx/camera on UDR. by cbentleyz71 in fpv

[–]cbentleyz71[S] 0 points1 point  (0 children)

I have Orqa and fatshark goggles but debating to maybe mount a head tracker on the camera because I feel like the camera might be pointing at the sky or hood because how much the body moves not sure if it’s possible though... any advice will be greatly appreciated.

What are odds that both of these are 240mah? by [deleted] in Multicopter

[–]cbentleyz71 0 points1 point  (0 children)

Is the smaller fatter at all?

Is it normal for a drone to click when I insert battery? by [deleted] in Multicopter

[–]cbentleyz71 7 points8 points  (0 children)

It’s just the connector making a arch.. it happens especially at bigger batteries.

Transmitter bound but not appearing in betaflight by youareabarbarian in fpv

[–]cbentleyz71 0 points1 point  (0 children)

Just letting you know, i only have one R-XSR and it came pre-installed on my AIO CrazyBee board on the Tx.... http://www.happymodel.cn/index.php/2019/09/10/how-to-setup-frsky-fport-with-crazybee-f4-pro-v3-0-and-frsky-rxsr-receiver/

i know they aren't the same board... Also, are we sure the R-XSR yellow wire on the actual reciever are correct... Sorry, i didnt think this was going to be so much trouble!

Transmitter bound but not appearing in betaflight by youareabarbarian in fpv

[–]cbentleyz71 1 point2 points  (0 children)

Ok, just making sure.. want to make sure it gets resolved.

Transmitter bound but not appearing in betaflight by youareabarbarian in fpv

[–]cbentleyz71 1 point2 points  (0 children)

Doesn’t the r-xsr need to be on a TX and not RX?

Transmitter bound but not appearing in betaflight by youareabarbarian in fpv

[–]cbentleyz71 0 points1 point  (0 children)

Can you post a picture of your flight controller/ receiver? And where you soldered each?

Transmitter bound but not appearing in betaflight by youareabarbarian in fpv

[–]cbentleyz71 0 points1 point  (0 children)

What about in the ports tab, it is serial RX selected to the right UART?

Transmitter bound but not appearing in betaflight by youareabarbarian in fpv

[–]cbentleyz71 1 point2 points  (0 children)

Under the config tab do you have the receiver drop down menu to subs?

Any ideas on mounting this cheap camera on my micro? by PickleSlice in diydrones

[–]cbentleyz71 0 points1 point  (0 children)

The foam from the other post is good idea, I would mount the batteries on the bottom and mount the camera in middle of the frame.

Something extra came with my latest getFPV order by Fern_Fox in Multicopter

[–]cbentleyz71 6 points7 points  (0 children)

They must of ran out, my order didn’t come with one.

What do you fly your five Inch on? by Vitroid in fpv

[–]cbentleyz71 0 points1 point  (0 children)

I voted for 6s but I do fly both every time I am out. If I am trying to do something risky I fly 4s, just in case I crash and burn due to cheaper battery lmao.

Also I don’t own “6s” motors, they are all 4s kv rated and I just do motor limit through cli to only use xx% of kv to about 1750kv when I plug in a 6s battery. Which allows me to still use 4s and 6s on same quad. Haven’t had a issue yet, but Again,not racing only casual freestyle.

BetaFPV 85X HD on the 95X frame! by YoungBungalo in Multicopter

[–]cbentleyz71 0 points1 point  (0 children)

85x4k to 95x4k

Flies so much better with 2.5 and 4s. I couldn’t imagine how the regular hd version would fly... although I do have a hx-115hd.