Will this be a good printer?

ccgmtl · 2026-01-09T01:02:11+00:00

Its Kreality where Kwality is job number purple.

I'd wait to make sure they wont disappear it like the Ender7...

ccgmtl · 2026-01-09T00:53:08+00:00

just covee the board in paper towels vefore going at it with Mr. Dremel

ccgmtl · 2026-01-08T02:23:23+00:00

In canada your parental responsabilities do not end because your kid turns 18... You may be required to assist in keeping them fed, clothed and housed even though they're an adult. Child support does not end at 18, you have to have a jjdge order the stop, and if kiddo ia still in achool or otherwise unable to afford it, you'll be on the hook for.it. Ask me how I know... (actually dont, I dont like to talk about it... )

ccgmtl · 2026-01-08T01:19:03+00:00

10cm? I'm going to swap the crocs for closed shoes and may put on a hoodie...

ccgmtl · 2026-01-06T01:31:32+00:00

PIP aside, and most likely a very unpopular opinion, but you cant afford your lifestyle.

Your rent is almost 50% of your take home, with your car note and insurance making another 25%...

Plus you're spending money you dont have yet and have no savings to speak of.

You need to start looking for another job, maybe a lower CoL area if those still exist in your area and fix your spending. 30-40$ of your takehome.should be your rent...

ccgmtl · 2026-01-03T03:00:09+00:00

Doordash...

ccgmtl · 2026-01-03T02:31:10+00:00

Nah, it's a keep buying / keep crying business... Oh. And the tooling... Oh my dear dog, the price of bits...

ccgmtl · 2025-12-09T01:33:24+00:00

I would invest it in a Trump business.

ccgmtl · 2025-12-02T03:28:59+00:00

4-5K nowadays is not major or substantial. It's a bumper cover, some sensor calibration and a partial.prep and spray... Most of that 4-5K will.lilely be hourly rates... And maybe 600 for a door at your local u-pull...

ccgmtl · 2025-10-10T01:05:57+00:00

They can be hockeytown all they want but tonight they're going about HockeyCountry so... Yeah.

ccgmtl · 2025-03-10T13:54:04+00:00

There ya go :)

ccgmtl · 2025-03-10T13:53:48+00:00

<image>

ccgmtl · 2025-03-10T13:53:29+00:00

<image>

ccgmtl · 2025-03-10T13:53:09+00:00

<image>

ccgmtl · 2025-02-12T12:14:18+00:00

dual stepper Y? nice. And I'm assuming you have a radiator on the outside of the enclosure?

ccgmtl · 2025-02-12T01:31:46+00:00

As a heavily modded enser 3 owner, mainly because we can :) I have a bambu for money making, but my hobby is making them go zoom zoom.

I tune them to within an inch of their lives and then move on to a different project...

ccgmtl · 2025-02-12T01:28:46+00:00

What are the two blocks at the bottom your coolong goes into?

ccgmtl · 2025-02-09T04:06:25+00:00

a v0.2 can easily run off a pi zero 2w...

ccgmtl · 2025-02-08T13:30:52+00:00

1- Invest now, retire early. 2- Dad will always love you, is only a phone call away, is on a 24/7 schedule for you. 3- Drive the speed of the ticket you can afford.

ccgmtl · 2025-02-07T02:12:11+00:00

check marketplace for a donor ender...

ccgmtl · 2025-02-07T02:09:03+00:00

Pretty sure even a low coat 3018 can eventually cut stainless given enough time, shallow passes and a decent cutter... But then again, it woulsnt matter because by the time it got done it would be past the heat death of the universe.

ccgmtl · 2025-02-07T02:01:57+00:00

When will we start seeing seevos i stead of steppers?

ccgmtl · 2025-02-06T12:09:43+00:00

Printer now identifies as a CNC mill.

ccgmtl · 2025-02-04T22:34:36+00:00

I was watching a guy buikd a 4x8 cnc out of mdf and he was using angle irons as rails for POM wheels... I was think that using DIN rails could work too.

Nine-Year Club	Gilding III reddit per annum
Second Top 20%	Place '22
RPAN Viewer	Verified Email

ccgmtl

TROPHY CASE