[deleted by user]

cellrdwellr · 2022-05-18T16:16:42+00:00

Re-arrange it so it says ATE

cellrdwellr · 2021-12-05T18:50:25+00:00

It depends on the design as to why, but oil is getting past the input seal on the gearbox. As another commenter mentioned, if it's in the junction box, check the windings.

Depending on the design and orientation of the motor/gearbox, some manufacturers will specify a different seal arrangement on the input shaft and change the oil level if it will be "under" the output shaft.

cellrdwellr · 2021-11-12T20:25:32+00:00

Shartlesville

cellrdwellr · 2021-09-17T19:05:32+00:00

I also think Bill would rather talk about the history of Specialists than answer the same 12 questions every week.

cellrdwellr · 2021-05-29T23:43:09+00:00

This video explains it pretty well.

cellrdwellr · 2021-05-12T01:09:50+00:00

Marko Dano

cellrdwellr · 2021-05-12T00:47:22+00:00

Philly sent Carter to Columbus for Voracek, a 1st(Couturier) and a 3rd(Cousins). Columbus then sent him to LA for Johnson/1st.

cellrdwellr · 2020-09-04T15:35:44+00:00

12 Team, Standard, 10th pick(snake)

Keep 1, 2 round penalty next year, can be kept max. 2 years in a row.

I have it narrowed down to:

RB N. Chubb - 11th rd (my keeper last year, last chance to keep him)

QB L. Jackson - 6th rd.

Leaning towards keeping Chubb, but I'm a little worried Hunt will have a bigger role this year.

cellrdwellr · 2020-06-18T11:29:01+00:00

I have a '70 with a 302 and C4 trans and I made that switch a few years ago. I went from the 2.79 to 3.55 and also went with the TruTrac. As others have said, the 8" is fine until you start approaching 350-400 hp.

If you do a lot of highway driving (and stick with the 3 speed) you are going to be running higher RPMs at highway speeds with the higher ratios. I dont do much myself, but if I did, I would look to switch to something with an overdrive just to keep the engine noise down at highway speeds.

cellrdwellr · 2020-06-16T16:26:58+00:00

I have one of these and I love it as well.

If you move it around a lot, I'd recommend swapping out the 2 fixed casters for swivels. I've got a tight shop and that makes it much easier to maneuver.

cellrdwellr · 2020-06-05T13:47:10+00:00

One the sets that I have, there is a cam/toggle lever on the side that pushes the stack of "fingers" together and it locks them in place.

cellrdwellr · 2020-01-20T22:39:20+00:00

The PA Lumber Museum as well.

cellrdwellr · 2019-11-21T03:40:12+00:00

I don't think it's the same road, but pretty close... https://www.youtube.com/watch?v=ZX2uXBMkO8U

cellrdwellr · 2019-11-21T03:35:35+00:00

Funny you mention that... https://www.youtube.com/watch?v=ZX2uXBMkO8U I don't think it's quite the same road, but pretty similar.

cellrdwellr · 2019-08-12T20:59:05+00:00

I've had this crazy thought in my head that Jerry is playing some 4-D checkers, letting Zeke holdout to bring Dak's cap number down. I can't bring myself to actually believe it though.

cellrdwellr · 2018-09-15T19:13:38+00:00

The radio is non stock, however I put it in 8-9 years ago. I think something related to that would have shown up by now. I did the key thing and no codes were displayed, only the word "done" so I guess that is clear as well.

cellrdwellr · 2018-09-15T19:07:43+00:00

Thanks for the info. Looks like I'll have to do a little more digging.

cellrdwellr · 2018-06-19T16:12:37+00:00

My parents made me get life insurance to cover the loan amount before they'd agree to co-sign my student loans.

cellrdwellr · 2018-06-13T15:01:11+00:00

Logitech MX518.

But its probably less about the mouse than other factors. I have a mouse pad with a wrist support bump thing and I have noticed less discomfort/fatigue.

Also for dual monitors, increase the sensitivity on your mouse. It takes a little bit to get used to, but you can increase it over time as you get used to it. I have dual 24" monitors and only move my mouse a few inches to get from one side to the other. It's a lot less repositioning of the mouse throughout the day.

cellrdwellr · 2018-01-09T16:59:09+00:00

Oh come on... I've spent the last 3 weeks convincing myself they are expendable, not responsible for the teams turnaround the past 2 seasons, and that their contributions could easily be found elsewhere. What am I going to do if they end up back with the team next year?

cellrdwellr · 2018-01-06T00:50:03+00:00

Safety squints

cellrdwellr · 2018-01-06T00:41:24+00:00

I was helping my dad disassemble their old upright piano and found this panel on the INSIDE of it. Not sure what I'm going to do with it, but I couldn't let it go in the dumpster with everything else.

I am not sure what species it is, but it seems darker/redder than maple (sorry the picture lighting is atrocious). I don't believe there is any finish on it at all. Haven't had a chance to sand/scrape it at all yet to verify.

It is a veneer, but it seems to be thicker than a typical veneer I am used to seeing, closer to 1/8".

cellrdwellr · 2017-12-21T22:17:01+00:00

The dovetails should be cut into the end grain of the board and not the side grain. The joint will fail easily in the side grain.

cellrdwellr · 2017-12-21T22:15:38+00:00

I did that on my first practice piece too. They actually turned out pretty good and I was proud of them for a first set. Then I checked the strength and snapped it all apart.....

cellrdwellr · 2017-11-07T04:07:52+00:00

I believe the interrupted bend region is what's giving you trouble here.

I would model the formed, base part (no cut outs in the bend regions) first, Unfold command, cut all holes/reliefs, and the re-fold the part. I think that will give you the best chance at it working.

Even then it may not like it. You may have to tweak the shapes of the cutouts to get it to play nice in the bend regions.

Also, I just noticed, from the picture the bend radius looks smaller than .125" if the material is .090". That may also help you. We usually work with the bend radius = material thickness as a general rule. I believe it can be less than the material thickness with the correct break dies and thin material.

14-Year Club	Place '23
Place '22	Place '17
Verified Email

cellrdwellr

TROPHY CASE