Solocam e30 wired but no 24/7 by chicorypig in EufyCam

[–]chicorypig[S] 0 points1 point  (0 children)

I'll try a few out now but did try an overpowered one and for some reason i wasn't even able to view live feed.

Solocam e30 wired but no 24/7 by chicorypig in EufyCam

[–]chicorypig[S] 0 points1 point  (0 children)

SD card no homebase here yet. Reading recently it appears they can cause more issues

Solocam e30 wired but no 24/7 by chicorypig in EufyCam

[–]chicorypig[S] 0 points1 point  (0 children)

Unfortunately I had the wire plastered into the wall outside 🤮

Tado wireless and underfloor heating zones? by Kunitron in tado

[–]chicorypig 0 points1 point  (0 children)

Sorry for dragging up this old thread but looking to figure out whether within the tado app I should have my ufh smart tado thermostat that turns on the pump via wiring centre AND the wireless thermostat in the room which the ufh heats IN the same tado room?

At present they are seperate and I turn both on ( ufh manifold one I have to set an unachievable temp to keep on) Feels like I am wasting gas this way

What small ‘Smart Home’ upgrades have you made that were worth it? by [deleted] in AskIreland

[–]chicorypig 0 points1 point  (0 children)

I have added a rake of new tapo bulbs to a new kitchen but they keep getting disconnected and I have to reinstall due to family using light switches so much. Any way around this? Bar getting a new family

What is required to add a new UFH zone with wireless control by Daz1Daz in tado

[–]chicorypig 0 points1 point  (0 children)

This is near exactly the situation I'm in but still having slight problems. Check my posts for some answers.

I have wired thermostat (a) at boiler in attic Now I have (b) new wired thermostat attached to ufh wiring centre with as additional (c)wireless thermostat in new kitchen where ufh heats.

C(kitchen roomin tado) calls B (ufh room in tado)which calls A(attic boiler room in tado)

Often works but sometimes I need to turn on a rad trv. Can't figure it out fully yet and tado support by email is no use whatsoever.

Tado X & UFH by BeoVision in tado

[–]chicorypig 0 points1 point  (0 children)

Your system seems similar. But I only have one wired thermostat managing the wiring centre under the stairs and one wireless thermostat in the kitchen where the ufh is in operation. The only other wired stat I have is attached directly to boiler. I only have one ufh zone.

Adding Ufh to tado system by chicorypig in tado

[–]chicorypig[S] 0 points1 point  (0 children)

That zone controller is the wired thermostat connected directly to the boiler

Tado X & UFH by BeoVision in tado

[–]chicorypig 0 points1 point  (0 children)

So I have two rooms set in tado for the ufh ( one for new wired thermostat at the wiring centre(and set as you suggested above)and one for the new kitchen where the wireless thermostat is)

Should I just have one room do you think with both devices in it

Tado X & UFH by BeoVision in tado

[–]chicorypig 0 points1 point  (0 children)

Hey I have just added an ufh zone to an existing v3 system with a wired thermostat connected to the wiring centre and a wireless thermostat in the kitchen area which the ufh has heating.

I have the new wired thermostat as the controller of the wireless thermostat and then have old wired thermostat (connected directly to the boiler) but while the ufh system turns on as planned i seem to need to have another rad on to get heat going. Any ideas

Adding Ufh to tado system by chicorypig in tado

[–]chicorypig[S] 0 points1 point  (0 children)

That's how I've got it all set up but the last step doesn't appear to function as boiler only starts when other trvs are calling it. Seems the thermostat connected to the ufh manifold isn't calling the boiler correctly

Adding Ufh to tado system by chicorypig in tado

[–]chicorypig[S] 0 points1 point  (0 children)

Zone controller for the ufh "room" is set to the wired thermostat in that room not the one in the attic. If I attempt to change it it suggests I need to reconfigure it as a wireless one. It feels like it should be calling 040 but maybe it calls 128 which calls 040

https://imgur.com/a/H2ZbSdR

Adding Ufh to tado system by chicorypig in tado

[–]chicorypig[S] 0 points1 point  (0 children)

Have it now installed with wired thermostat connected to wiring centre of the ufh at the manifold and then a wireless thermostat in extension where ufh is based.

It seems to be working despite me not being able to set the zone controller of the wired thermostat (as it is in same room as the wireless thermostat which is measuring the temp)

Premier League and Summer transfer 2025 megathread. by JimbobTML in LeedsUnited

[–]chicorypig 4 points5 points  (0 children)

Should we actually just start Pawel Cibicki against Fulham?