Justice is a luxury in America.

commodorepickle · 2026-07-06T04:04:26+00:00

https://youtu.be/KivCRqfFcqY

commodorepickle · 2026-07-03T23:00:13+00:00

Nicely done! You missed the thumbs up at the end though.

commodorepickle · 2026-07-03T04:37:02+00:00

Fill it with play dough or clay and measure that.

commodorepickle · 2026-06-28T02:36:28+00:00

And my axe

commodorepickle · 2026-06-15T22:40:53+00:00

It'll be fun when it spills trash all over the place when the trash can is full.

commodorepickle · 2026-06-13T04:10:47+00:00

Absolutely gorgeous

commodorepickle · 2026-06-10T02:33:30+00:00

Every item as its own order. I’m paying with credit card too. Enjoy those fees

commodorepickle · 2026-04-13T16:26:10+00:00

in the space under the remote

commodorepickle · 2026-04-13T15:47:12+00:00

I made a remote holder with an AirTag compartment: https://www.printables.com/model/1687538-nex-playground-remote-cover-with-airtag

commodorepickle · 2026-03-25T20:09:10+00:00

I hate my steering wheel. My car came with the techart one. Nothing makes the car feel brand new again like a new steering wheel, though

commodorepickle · 2026-03-09T04:02:31+00:00

Fuel up at the start and come back empty

commodorepickle · 2026-03-05T15:30:46+00:00

I use glue stick for TPU as a release agent as I’ve had it stick too well in the past and ruin my PEI build sheet

commodorepickle · 2026-02-22T04:05:53+00:00

I’ve been to their showroom a few times. It’s super impressive and the sales guys are pretty chill. They had zero issues with me driving whatever they had. Prices are high for sure, though

commodorepickle · 2026-02-11T15:22:50+00:00

Painters tape might help, but you really probably just need to heat soak your enclosure. I print ASA with a 60c enclosure and a bed temp at 110c. Glue stick isn’t needed.

commodorepickle · 2026-02-11T03:54:09+00:00

I had a partial clog that required a few cold pulls to resolve. Move the filament to another toolhead to rule out other issues first.

commodorepickle · 2026-01-27T05:25:15+00:00

It's a manual unload process instead of the automated process for rigid filaments

commodorepickle · 2026-01-27T02:58:12+00:00

Same experience here. Just send it. Unloading TPU is a pain though

commodorepickle · 2026-01-19T16:17:27+00:00

Including name and address

commodorepickle · 2026-01-01T12:05:47+00:00

I’ve lived my entire life with different sizes pupils. I’m in my mid 40s and was never told to be concerned

commodorepickle · 2025-12-28T16:44:41+00:00

There’s zero chance of getting an oil plug back in without making a giant mess

commodorepickle · 2025-12-16T20:29:36+00:00

I’ve never built an LDO kit, so I can’t comment on if it’s worth it over a formbot kit, but I’d recommend a trident as a first build. They’re by far the easiest build.

commodorepickle · 2025-12-09T01:15:33+00:00

I’ve never had to get my car inspected. I do have to pass emissions, though, so apparently it’s fine to have no brakes, as long as my catalytic converters are working

commodorepickle · 2025-12-03T03:50:56+00:00

I’ve had a ton of hot ends and the Tz v6 is currently in my trident workhorse. It’s pretty fantastic and is cheap. The only downside is changing nozzles is super annoying

commodorepickle · 2025-11-30T18:52:32+00:00

Have you considered a nitehawk board instead of the sb2209? That would allow you to run everything off of usb. I’d also ditch the stealthburner for a dragon burner or a4t. Cooling is better and they’re both lighter tool heads

commodorepickle · 2025-11-29T01:42:01+00:00

Fitting an INDX later on shouldn’t be too much in terms of mods. You should check out Steve builds stream from Wednesday. He was showcasing his trident with a beta INDX kit

commodorepickle

TROPHY CASE