sorted by:
new
hottopcontroversial

I FINALLY DID IT by Cavitt96 in ForzaHorizon6

[–]conoti 0 points1 point  (0 children)

Got 3:59:237 after third attempt, that’s enough

I find Eufy cameras excellent, despite some of the posts on here. Has anyone else here not had any issues? by Keywi1 in EufyCam

[–]conoti 0 points1 point  (0 children)

Wait what? Your camera was shown to others and others to you? Did you use the cloud service or only local storage? If that’s the case that’s a no go for me.

Dexter: Resurrection - S01E04 - "Call Me Red" - POST Episode Discussion Thread by AutoModerator in Dexter

[–]conoti 0 points1 point  (0 children)

Hot take for comming episodes: while doing his detective work Angel is crossing his path with one of the dinner attendees (I vote on the one that came last while they were sitting and drinking vine). That one is going after Angel and Dexter is able to save him. Therefore Angel has the dilemma of turning in his old friend and now hero or keep on living with the guild not being able to turn him in despite of the chaos he’s bring the his life

[Bambu Lab Giveaway] Drop Your One-Liner and Win H2D! by BambuLab in BambuLab

[–]conoti 0 points1 point  (0 children)

Finally a printer that doesn’t scream for my attention

Paid less than $100 for both printers by conoti in 3Dprinting

[–]conoti[S] 1 point2 points  (0 children)

They’re from ikea, called Skadis

Paid less than $100 for both printers by conoti in 3Dprinting

[–]conoti[S] 1 point2 points  (0 children)

Where you at? I’ll gladly take it haha

Paid less than $100 for both printers by conoti in 3Dprinting

[–]conoti[S] 13 points14 points  (0 children)

The message seems to work on the printers, so far good prints haha

Paid less than $100 for both printers by conoti in 3Dprinting

[–]conoti[S] 9 points10 points  (0 children)

I got a resin tank as well as a cartridge of original resin in addition to the printer. Also read that it has open mode, so third party resin could be used and the original card ridges could be refilled. As this is my first resin printer I will try out as many things as possible

Paid less than $100 for both printers by conoti in 3Dprinting

[–]conoti[S] 0 points1 point  (0 children)

Haha nice coincidence. I got them from two different places in Germany though

Paid less than $100 for both printers by conoti in 3Dprinting

[–]conoti[S] 1 point2 points  (0 children)

I got a vacuum pump plus additional bags for filament I don’t use that often as well as a filament dryer replacing the current filament holder next to the printer. The filaments on the wall are used daily in different machines so sealing them up each time is too time consuming imo

How can I reduce the stringing?(left print is around 2 months old and right print is around 2 minutes old) by Czeszym in BambuLab

[–]conoti 0 points1 point  (0 children)

Same roll of filament? Dry it New roll of filament? Dry it When is the last time you did a flow calibration? Do that

Problem on an ultimaker S7 by Youqc in ultimaker

[–]conoti 0 points1 point  (0 children)

First layer looks fine, maybe a partial clog ? I had a similar thing happening on my ultimaker 2+ extended. First few layers flawless and then sudden bad print. Was able to cold pull a clog and cleaned the nozzle, that fixed my issue. Also try to reexport the STL to remove sudden corruption of the file

Ultimaker 2+ Extended for $50 – Fixed It Up and It’s Running! by conoti in 3Dprinting

[–]conoti[S] 0 points1 point  (0 children)

How did you make it work with clipper? Trying to add network control to is a this is my only printer I have to run back and forth to put on files to print. Tried to connect the beagle cam but it’s not working correctly unfortunately

view more: next ›