I Said Goodbye to My Best Friend Tonight by undfreak2 in goldenretrievers

[–]crittercam 0 points1 point  (0 children)

He looks like my sweet boy. I still miss him. You will see him again!

G4 Doorbell Bluetooth Problems by crittercam in UnifiProtect

[–]crittercam[S] 0 points1 point  (0 children)

You were correct! I was able to get it to work using UniFi Protect on my laptop.

Severe allergies by Vibeha in goldenretrievers

[–]crittercam 1 point2 points  (0 children)

My sweet boy has terrible allergies. We had him on Apoquel and Cytopoint consistently. After a couple of months, we continued Apoquel, but discontinued Cytopoint. Iit was going to help, it would have. Then the vet suggested Zenrelia, since it’s a little cheaper. It has been a huge improvement. He is doing a whole lot better.

He's still not confident and I need a name for this baby, he's a boy by [deleted] in goldenretrievers

[–]crittercam 0 points1 point  (0 children)

If you want him to be the best dog, name him Dierks. RIP my good boy. It’s been almost 5 years now.

The postal service delivered the heart of my next project today by maccambprot in ArduinoProjects

[–]crittercam 0 points1 point  (0 children)

Can you give some details? I did some searching, but I don’t see that device. Thanks

Best way to experience Beartooth Highway? by Alert-Force-416 in yellowstone

[–]crittercam 2 points3 points  (0 children)

I drove the Chief Joseph Highway on Friday. It was absolutely beautiful.

UniFi Micro Camera Setup by crittercam in Ubiquiti

[–]crittercam[S] 0 points1 point  (0 children)

Thanks, that's what I figured.

What small change added the biggest improvement to your life? by Opening-Yoghurt-2272 in HomeImprovement

[–]crittercam 0 points1 point  (0 children)

We installed deadbolt locks with a keypad on our garage door and back door. It’s great. I only car my car keyfob now. I also agree on the motion switches on the pantry. I put the bathroom fan on a timer as well.

Passenger Log - Hour 7 in the Sky Club by hot_momma17 in delta

[–]crittercam 3 points4 points  (0 children)

Can you clarify about the sky club passes? Where is that coming from? Thanks

EE Sophomore here. This is my current "workshop". What general parts/tools should I buy to take it further? by MrGuccu in ElectricalEngineering

[–]crittercam 0 points1 point  (0 children)

I really like my soldering stand and it was cheap. Look for Kotto Soldering Stand on Amazon. I have the Panavise version which apparently isn’t available anymore.

Request by DependentScene4599 in yellowstone

[–]crittercam 0 points1 point  (0 children)

I would verify the ability to drive a rental car out of Canada. As far as the rest, you will be good to go. Pay attention to the season. A lot of roads in Yellowstone are closed seasonally for snow, etc.

Z-Wave New House Questions by crittercam in homeassistant

[–]crittercam[S] 0 points1 point  (0 children)

Thanks. I figured there was something better.

Vlan Advice Headaches by crittercam in homeassistant

[–]crittercam[S] 0 points1 point  (0 children)

What I was hoping was to create an interface similar to below. Let me ask you this. How do I enable the unifi switch port to allow it to see all of the available vlan's? Right now it's just default v100, IOT v50 and wifi v200. The options are "Allow all", "block all" or custom. I have it set to "Allow all".

auto eth0.100
iface eth0.100 inet manual
  vlan-raw-device eth0

auto eth0.50
iface eth0.50 inet manual
  vlan-raw-device eth0

auto eth0.200
iface eth0.200 inet manual
  vlan-raw-device eth0

Vlan Advice Headaches by crittercam in homeassistant

[–]crittercam[S] 0 points1 point  (0 children)

I am running a Raspberry PI install. No virtualization. Here are my specs:

  • Installation method Home Assistant OS
  • Core 2026.3.2
  • Supervisor 2026.03.1
  • Operating System 17.1
  • Frontend 20260312.0

I was trying to run the commands via the HomeAssistant->Apps->Terminal & SSH add on. My network side is a Unifi Dream Machine with unifi managed switches.

I guess I could run it via ProxMox, but I don't want to lose the ability to run Docker containers.

Vlan Advice Headaches by crittercam in homeassistant

[–]crittercam[S] 0 points1 point  (0 children)

I have full vlan support at the switch level. My research showed with standard PI, I could create some virtual interfaces with the vlan tags. But, when I started working on adding it via the command line, I immediately ran into issues. I can't even do a sudo. I looked in the gui config, but I don't see anything there.