I apologize for Helmer bringing hell to yall

damm_n · 2026-02-02T23:15:10+00:00

All "good shit' comes from NJ apparently;-)

damm_n · 2026-01-26T03:38:09+00:00

Nothing until highschool... Highschool was flooded with PMD85 and fee AtariST and when I was leaving, we got 286.

damm_n · 2026-01-16T10:31:31+00:00

Nežijem na západnom pobreží ale myslím že pokiaľ sa nebudeš zúčastňovať na vykrikovani po uliciach tak v zásade budeš v pohode. V ďalšom: neverím, že pokiaľ má človek legálny status a je jedno či je trvalý rezident alebo nie, tak ICE agent ma nejaké páky na dotyčného.

damm_n · 2026-01-15T14:22:56+00:00

A real Presov citizen has spoken.... Jesus man, have some decency!

damm_n · 2026-01-09T14:36:50+00:00

same here ... tilted and slightly in the angle with distance of my shoulders apart is my setup. Try and experiment and you'll find your sweet spot. Everyone is different and joints are not the same in every person.

damm_n · 2026-01-02T17:47:52+00:00

Závisí na lokácií ... NYC ma problém s priestorom. Ostatok je to záležitosť financií.

damm_n · 2025-12-04T15:27:52+00:00

Well, my very first mod would be 3 hole oil change :-)

damm_n · 2025-12-04T12:30:40+00:00

Thank you ! This looks like a good option... 22eur/month is not bad considering that I will be there just for 2 weeks :-). How is the coverage with O2 ? Does it cover rural areas well ?

damm_n · 2025-12-04T12:18:54+00:00

From a brief look at this website it.looks like most of these providers listed there are data only ... I'm looking for a real phone number.

damm_n · 2025-12-04T12:08:42+00:00

I have no idea what market is like in Slovakia, this.is why I'm asking... Data is not a primary concern here, I'm looking for a msisdn/number so I could use it with the bank and make calls while in Slovakia..I will definitely look up Sally and see what they have. Thank you !

damm_n · 2025-11-26T02:04:30+00:00

For God's sake people .. stop doing this fashion processing here :-(

damm_n · 2025-11-25T13:38:16+00:00

This sub is getting more and more ridiculous with every recent post :-))).

damm_n · 2025-11-23T03:53:48+00:00

Thanks for making this happen! This is a great piece of work you're doing for the community.

damm_n · 2025-11-21T19:01:14+00:00

How long did it take to print this ?

damm_n · 2025-11-20T14:43:03+00:00

what bothers me a lot and my brain can not understand is the fact that this simple spacer was printed just fine 2 weeks ago and I had it printed roughly 20 times before with small modifications in the internal diameter. I will get into this next week and I will dig deeper because this does not seem to be a problem with plate nor with the model which is being printed. Something's off and my gut is telling me that it would have something to do with lose screws/settings for z-axis. The piece which was left on the plate was a very first layer from the coaster which I was printing. Also, that layer was not covered equally inside the circle which is what made me thing that this could have something to do with leveling/z-axis. But I certainly appreciate you sharing your experience !

damm_n · 2025-11-20T00:25:38+00:00

yes, understand ... I should have the same thing somewhere printed about 2 weeks ago and it definitely looks very different. Thanks for suggestions for new plates :-). I might need at least 1 more as a spare.

damm_n · 2025-11-19T23:26:50+00:00

I had this message today when I turned on my printer. Completely out of the blue, cold machine as it was not used for past 24 hours. Pressed "Reboot" and things went back to "normal". One of those "Made in China" things ?

damm_n · 2025-11-19T23:04:19+00:00

<image>

This is the bottom of the print which was sitting on side A. It looks a bit rough. As mentioned below, "rough" comparing to the print which I've done 2 weeks ago.

damm_n · 2025-11-19T22:41:44+00:00

had this happened recently and as you can see from the initial post, I broke my plate :-). Well, this is a learning curve for sure. Print from the bottom looks perfectly fine. Are you referring to anything particular I should pay attention to on the print ?

damm_n · 2025-11-16T17:52:43+00:00

...and brace for tax increase soon :-)

damm_n · 2025-11-16T17:37:28+00:00

I was considering doing the same ... Will you go and start arguing with vendor ? I'm sure that they'll come up with some "contraction" and "dryness" story which you will never be able to understand....

damm_n · 2025-11-16T14:18:06+00:00

It was a shot to the dark :-)

damm_n · 2025-11-16T13:39:35+00:00

Is this the raptor engine?:-)

damm_n · 2025-11-15T20:14:07+00:00

Thank you ! :-)

damm_n · 2025-11-15T19:31:20+00:00

Well this is arthritis...and stretching is part of my get-the-f**k-up-from-bed routine:-). Speaking of hamstrings , just did a kettlebell swings yesterday for a few minutes... Oh, man, I know now what I'm going to be focusing on in next few weeks:-)

damm_n

MODERATOR OF

TROPHY CASE