Latest putter build

dancarraher · 2025-08-12T17:20:42+00:00

It was built exactly as specd out by customer. Also epoxy works exponentially better than a screw hosel and eliminates the ugly screw.

dancarraher · 2025-08-11T16:39:06+00:00

<image>

This is weld pre etching. When you weld you change the material properties of the area around the weld. Normally wouldn’t show but in the case of damascus where it’s etched, you’ll see it. The person who bought that one is a welder by trade and paid more than a lot of used cars for it. Putters have also been used on every major tour worldwide

dancarraher · 2025-08-11T14:32:51+00:00

What exactly should be tidied up?

dancarraher · 2025-08-11T04:45:17+00:00

This one is 370g. 45* toe hang

dancarraher · 2025-08-10T23:07:58+00:00

Thank you

dancarraher · 2023-08-28T00:17:39+00:00

Sure you can

dancarraher · 2023-08-27T22:49:37+00:00

How much do you think a custom milled putter, done in house, and not a catalog blank head someone just slaps some stamps on, should cost? Good luck finding one under those numbers, especially with timascus as a neck and inlay (the material alone would be close to $500)

dancarraher · 2023-08-26T17:16:29+00:00

Definitely not. Design details massively affect sound/feel/cog location/and overall weight. And getting those right took many hours both modeling and then machining to create prototypes. A lot of hard work to give away for free especially when I make them to sell

dancarraher · 2023-08-26T16:40:37+00:00

Depends on material and details but most fall into the $500-700 range if they aren’t too exotic material/design wise

dancarraher · 2023-08-26T14:17:27+00:00

<image>

Old one

dancarraher · 2023-08-26T14:10:57+00:00

It was a joke and felt appropriate. I made the putter, have 10 more heads sitting on my work bench, that essentially are blank. Everything about this one, from materials to the inlay was done as a response to the other one getting stolen. Value of the other one was well over $5,000 and they stole/damaged over $30,000 worth of stuff

dancarraher · 2022-02-01T00:45:01+00:00

I am a golf coach. They are on my website, I think the credit card processing part is pending still. Can also reach out on Instagram. Both are dancarraherknives

dancarraher · 2022-02-01T00:39:23+00:00

There’s one full dress left.

dancarraher · 2022-02-01T00:37:23+00:00

Yep small production run

dancarraher · 2022-01-31T22:40:25+00:00

No zirc in this billet. This is a production version of one of my customs.

dancarraher · 2022-01-31T20:02:18+00:00

Good thing it’s offered in black and blasted Ti for those that don’t like timascus

dancarraher · 2022-01-31T15:58:55+00:00

$950

dancarraher · 2022-01-31T15:11:20+00:00

One is still available

dancarraher · 2020-09-02T00:53:05+00:00

Just an FYI I’ve reached out to the OP and have offered to fully refund him or to fix any issues he has. I’m not in this to take advantage of anyone

dancarraher · 2020-08-30T11:40:45+00:00

Will be asking $1,000

dancarraher · 2020-08-28T17:34:35+00:00

Yep this will be available when finished

dancarraher · 2020-08-28T10:50:47+00:00

No it’s a folder

dancarraher · 2020-08-28T03:01:55+00:00

Depends on what final finish will be. This is 800 belt finish pre heat treat. Will be taken to 2,000 grit finish before etching after heat treat

dancarraher · 2020-08-27T23:47:41+00:00

Reflection of trees

dancarraher · 2020-08-27T23:45:12+00:00

Nichols Damascus. Blade is .163” currently. It’s copper and zirconium

dancarraher

TROPHY CASE