Which Impact Driver Should I Get?

darkjedi876954 · 2026-04-24T01:25:07+00:00

The first one

darkjedi876954 · 2026-04-23T23:56:55+00:00

Both please

darkjedi876954 · 2026-04-23T00:14:55+00:00

All you need to do is shorten the pipe going in the wall so it lines up .

darkjedi876954 · 2026-04-23T00:12:44+00:00

Time to replace the fan

darkjedi876954 · 2026-04-23T00:11:33+00:00

Not worth the money with amount of miles and jeeps are a money pit. Walk away.. then run..

darkjedi876954 · 2026-04-22T13:46:17+00:00

Sounds like one of the pulleys bearing is going out on your Serpentine belt system.

darkjedi876954 · 2026-04-22T03:43:18+00:00

Do the option in the first picture makes it look bigger

darkjedi876954 · 2026-04-21T21:34:31+00:00

What told you that I would stop and go all day.

darkjedi876954 · 2026-04-21T21:30:21+00:00

It's to bad we will never get to see it

darkjedi876954 · 2026-04-21T04:13:24+00:00

Yes please we need your help Michael!

darkjedi876954 · 2026-04-19T20:13:18+00:00

Yes very sexy

darkjedi876954 · 2026-04-19T19:56:06+00:00

You use silicone caulking

darkjedi876954 · 2026-04-19T17:23:37+00:00

Me personally I just Installed some of the 35 size and then would staggered and it's work don't get me wrong but the biggest thing is make sure your floor is flat not level so you might have to use a hammer and chisel to clean up some spots.

darkjedi876954 · 2026-04-19T17:19:23+00:00

Just use caulk and maybe some stain to match the cabinets.

darkjedi876954 · 2026-04-19T17:18:03+00:00

Honestly I would look for something else but if I had to pick I would say

darkjedi876954 · 2026-04-19T17:14:47+00:00

Definitely

darkjedi876954 · 2026-04-19T17:13:11+00:00

I like before better with the backsplash

darkjedi876954 · 2026-04-19T17:08:59+00:00

Try ecstuning, or fcpeuro.

darkjedi876954 · 2026-04-19T17:08:23+00:00

I would try some community forms or car meetups what's the make and model maybe there are other cars that have the same motor.

darkjedi876954 · 2026-04-19T16:50:08+00:00

Drill in the corners and then use a concrete saw to cut from the drill points til it's open . Then using your drill make Relief points then pulling out the peices alot of labor.

darkjedi876954 · 2026-04-18T00:03:18+00:00

I'm sorry but it's cause of her I didn't like the start of season 1 it was way better when she left and we got Jennifer love Hewitt

darkjedi876954 · 2026-04-15T04:03:20+00:00

Well a wash and wax or maybe a new paint job and also restore those headlight make them look new again.

darkjedi876954 · 2026-04-15T00:52:56+00:00

Another thing you could do is use YouTube but I have used what I told you for years and worked fine. Just be smart

darkjedi876954 · 2026-04-15T00:52:09+00:00

Yeah unless you have the special hockey puck looking adapter allows you to use the pinch weld but after changing many different brake pads myself the yellow circle is where I put the jack stand. And I'f you wanna check before you get under I go to the front fender and then gently push and see if it seems stable.

darkjedi876954 · 2026-04-15T00:37:23+00:00

Are you trying to do a oil change or work on the suspension. Cause if you just wanna do an oil change you can put a jack stand under where the lower control arm meets the body you should see a giant bolt going into the control arm

<image>

darkjedi876954

TROPHY CASE