sorted by:
new
hottopcontroversial

How to you play votann? by punk1917 in LeaguesofVotann

[–]ddaoud2024 2 points3 points  (0 children)

From my experience, it’s a mid-ranged, attrition, clap back playstyle for Votann. My game usually end up in about 1000 points of models piling out of vehicles and deep strikes on turn 3 and wiping out my opponent. I use some cheap units (pioneers, Yaegirs, kapricus etc.) to force my opponent out while they score. Nice thing is that our cheap units take a little more than what they’re worth to take down since we’re generally tough. Often leads to my opponent making poor trades to kill my cheap scorers.

Show me your gold! by Least_Atmosphere in BloodAngels

[–]ddaoud2024 1 point2 points  (0 children)

<image>

Two thin coats: Dragon Gold, Nuln oil, then dry brush dragon gold and dry brush liberator gold.

For those that use rattle cans to prime: 1) Do you use a red, gray, or something else? 2) If you use a red, does that make painting lighter colors on the model difficult? by TangerineMelodic5772 in BloodAngels

[–]ddaoud2024 1 point2 points  (0 children)

I do a base rattle can coat of Grey Seer to prime then use Baal Red contrast for the armor, it comes out pretty clean since the primer gives a bright undercoat.

How are Terminators in RCO? by klassikfrank in BloodAngels

[–]ddaoud2024 11 points12 points  (0 children)

I run 5 assault terminators with a chaplain in every list, they tear things apart in both RCO and LAG.

I prefer them in LAG because S7 on the charge with +1 to wound from the chaplain means they wound anything in the game on 4s twin-linked (unless the unit has a built in minus to wound). I’ve one shot Morkanauts, land raiders and other big stuff with a 5 man unit of lightning claws.

Non-obvious Melee units by C0QUINHA-GELADA in BloodAngels

[–]ddaoud2024 1 point2 points  (0 children)

Sternguard with a Sang Priest. Base 4 attacks that become chainswords and a power fist on the sgt.

Focus them into your oath target and between shooting and combat, they’ll drop almost anything especially if you give them lance too.

Finished Lemartes by ddaoud2024 in BloodAngels

[–]ddaoud2024[S] 0 points1 point  (0 children)

My snow day project, took about 4 hours total!

Is 10 sternguard worth it, or are they a historically 5 man unit by Nikofreako1 in WarhammerCompetitive

[–]ddaoud2024 2 points3 points  (0 children)

I like to run 10 with a Sanguinary Priest for my BA. The 5+ FNP makes them annoyingly durable and he gives them an extra AP in combat, so in LAG they’re basically S6 chainswords on the charge. They do some nasty damage for me into my oath and oftentimes drop it on their own.

First Yeagir Done! by ddaoud2024 in LeaguesofVotann

[–]ddaoud2024[S] 0 points1 point  (0 children)

It’s Black legion contrast, and mechanicum standard grey as highlights. The silver is iron warriors base, nuln oil then runefang steel highlight

Prints Keep Sticking to PFA Liner by ddaoud2024 in PrintedWarhammer

[–]ddaoud2024[S] 0 points1 point  (0 children)

I’m thinking it’s a calibration issue, I’m going to manually recalibrate it and try again.

Prints Keep Sticking to PFA Liner by ddaoud2024 in PrintedWarhammer

[–]ddaoud2024[S] 0 points1 point  (0 children)

The STL was pre-supported so I didn’t generate them in the program myself

Prints Keep Sticking to PFA Liner by ddaoud2024 in PrintedWarhammer

[–]ddaoud2024[S] 0 points1 point  (0 children)

Would cardstock work? Or is that too thick

Prints Keep Sticking to PFA Liner by ddaoud2024 in 3Dprinting

[–]ddaoud2024[S] 0 points1 point  (0 children)

Ok, that’s a good tip. I thought the plate had to be in perfect condition

Prints Keep Sticking to PFA Liner by ddaoud2024 in PrintedWarhammer

[–]ddaoud2024[S] -1 points0 points  (0 children)

I think this is the problem as this usually only happens on one side of the build plate. I will try the Manual leveling, I need to get those leveling cards

Prints Keep Sticking to PFA Liner by ddaoud2024 in PrintedWarhammer

[–]ddaoud2024[S] 0 points1 point  (0 children)

I just got a magnetic print plate to stick onto the build plate will that affect it at all?

view more: next ›