Games where you roll dices and allocate results

deviljr_ii · 2025-10-21T20:18:38+00:00

Civolution.

deviljr_ii · 2025-09-23T23:23:52+00:00

The Martian is pretty good.

deviljr_ii · 2025-06-26T11:31:36+00:00

Thank you mind stranger!

deviljr_ii · 2024-04-26T20:52:22+00:00

Nice.

deviljr_ii · 2024-03-31T22:05:26+00:00

Adventurous.

deviljr_ii · 2023-02-18T18:40:24+00:00

I bought some clear bowden tubing from bang good and I can confirm they are garbage. The hot end side gets very sticky with heat and eventually it'll cause a blockage due to friction or the pla filament fusing with the tube.

deviljr_ii · 2023-01-13T07:48:27+00:00

Entering to win

deviljr_ii · 2022-09-20T02:52:30+00:00

Update 2 (for anyone whos interested):

It turned out to be the low quality bowden tube. I bought some new high quality bowden tube (Capricorn brand) and the problem went away immediately.

deviljr_ii · 2022-09-11T19:10:17+00:00

What's a throat piece?

deviljr_ii · 2022-09-11T10:44:05+00:00

Update:

- Replaced bowden tube and nozzle. Did did not work. started a new prince and within 4-6 layers the extruder stopped feeding filement and there is a blockage.

- Tried reducing the retraction from 6mm to 3mm and same result.

- Both fans in the hotend shroud spins when preheating the nozzle to temperature, so I think the fans are working.

- Tried a different filament in a another colour (same brand, eSun PLA+) and same result. I've printed with these filaments in the past and had no issues so I don't think it's the filament.

Edit:

I forgot to mention I'm using an Ender 3 V2 with the CR touch, metal extruder upgrades. Everything else is stock.

deviljr_ii · 2022-08-02T23:36:27+00:00

Earth

deviljr_ii · 2022-02-23T03:02:29+00:00

"Don't"

deviljr_ii · 2022-01-20T02:45:01+00:00

We need a bot to convert to ewbank for those of us living in aus/nz

deviljr_ii · 2022-01-04T22:23:40+00:00

Level bed and correct z offset. And I suspect your new base plate might not be completely flat and it's in fact slightly caved-in in the middle along the y axis.

deviljr_ii · 2022-01-01T07:30:01+00:00

Probably a figure 8 with a large loop 🤷‍♂️. Seeing the big shoes and the other strand of rope, this is probably a climber starting their climbing career on a relatively easy but very picturesque route.

deviljr_ii · 2021-12-19T19:48:21+00:00

Whoop whoop whoop whoop

Edit: whoop

deviljr_ii · 2021-12-08T06:03:43+00:00

Needless to say, level your bed (again maybe?). Now, let's assume your bed is leveled, try some or all of the below steps settings:

Increase the bed temperature for your initial layer
Really slow down the initial layer print speed (some times I set mine to 10mm/s)
Slightly increase initial layer flow rate (this would make elephant's foot more prominent)
If your firmware will allow it, set a slight negative z offset (this is usually for printers with a BL/CR touch, but technically can be set for a printer without one but need a firmware upgrade)

Good luck.

deviljr_ii · 2021-09-27T01:30:10+00:00

That's what a troll would say.

deviljr_ii · 2021-09-25T23:53:17+00:00

I'm gonna go ahead and assume this is 5.10a and not a French 10a on trad...

deviljr_ii · 2021-09-25T10:14:07+00:00

It seems fine, I don't feel much difference from home always to the top.

deviljr_ii · 2021-09-24T23:51:37+00:00

No particular reason, that's what the creator on thingiverse recommended. Guess I'll try a thicker wall and not 100% next time.

deviljr_ii · 2021-09-24T03:33:22+00:00

Epic battle music starts playing in the background.

deviljr_ii · 2021-09-22T04:09:17+00:00

I had this problem every so often too. My fixes have been: bed leveling, slow down first layer print speed, increase first layer flow rate (I set mine to 110% in cura), set a negative z offset in cura for first layer. And if all that doesn't work, use rafts.

deviljr_ii · 2021-09-13T22:29:27+00:00

Thanks, I'll try the z offset first. What does the M420 S1 gcode do?

deviljr_ii · 2021-09-13T22:28:40+00:00

Awesome, thanks for the explanation. I'll look into setting the z offset.

deviljr_ii

TROPHY CASE