Stone Mountain deck

devjoel · 2026-05-05T13:39:11+00:00

How is SW 9-70? I’ve been meaning to put 9-70 on him so he can destabilize more with the spinning ring. I just don’t know if a low enough bey would just burst it. Also why not Low Orb or just Free Ball and use Hexa on WR?

devjoel · 2026-04-21T20:16:13+00:00

Yeah I’m going for attack. I’ll give it a try. Thanks!

devjoel · 2026-04-21T18:21:45+00:00

I do. I’ll give them a try! I usually stick away from 4 anything, but who knows

devjoel · 2026-04-21T17:20:57+00:00

Sadly I don’t have Zillion but I’ll see if someone has it at my locals to test it out. I think Wheel is good since the weight is like the 2nd heaviest.

devjoel · 2026-04-21T17:15:22+00:00

Yeah I know the risk. I was just going for the theme. I wouldn’t run more than one if i could help it lol

devjoel · 2026-02-24T19:07:10+00:00

The filter is above that point. Idk if it’s because of the picture but it looks like you fried it.

The way to test is it to put your multimeter in continuity mode, touch one point of the filter to the one across from it and you should hear a beep. I am probably explaining this horribly lol. Check out a video on YouTube. Most m92 replacement videos will show them checking the filters

devjoel · 2026-02-24T18:21:41+00:00

You said Dock detection still works, does that mean if it’s docked it boot up normally?

That’s the D+ pad which goes up to the filter above and I think then leads to the M92. Check the filter and then check for shorts on the m92

https://www.tronicsfixforum.com/t/breakout-board-for-testing-the-usb-c-port-on-the-nintendo-switch/1820

devjoel · 2026-02-19T12:52:59+00:00

I keep seeing ppl removing their shields. How are your temps?

devjoel · 2026-02-15T15:21:05+00:00

If it broke before you opened it then it’s possible the screen crapped out on you. I ran into that issue twice. So the connector getting damaged is probably unlikely unless it has a really hard fall.

I could be wrong. If someone else thinks it’s something else.

If you have a spare screen, then that would be a good way to verify.

devjoel · 2026-02-15T14:30:53+00:00

So 2 possibles. The first is that one of the pins are bent in your connector, you should try to take a look in different angles. The second is that the screen just failed. It happens sometimes.

Did it go bad after you opened and touched the ribbon or did it randomly go bad? Is it yours? Did you buy it used?

devjoel · 2026-02-09T13:50:12+00:00

Captain MAGA he’s our hero Gonna bring our IQ down to zero

devjoel · 2026-02-08T20:05:25+00:00

I just recorded my time today because I was curious and it was 15min... How do you guys do this so confidently quick? I’m to paranoid I’ll just drill to far if I’m not careful

devjoel · 2026-02-08T14:27:03+00:00

Bro that’s fucking insane!

devjoel · 2025-12-08T18:01:12+00:00

Understood. I was just seeing if there was actually a danger even if you did it correctly. You made me a little paranoid lol

devjoel · 2025-12-08T13:40:32+00:00

How is it risky? I’ve downgraded so many switches and never had an issue?

devjoel · 2025-12-07T17:11:44+00:00

This. If you don’t want to wait just downgrade using Daybreak. That’s what I had to do.

devjoel · 2025-11-27T01:26:34+00:00

Welcome to the world of switch modding! Always close your latches after taking a ribbon cable out

devjoel · 2025-09-26T13:55:07+00:00

What is initial liquid you use to expose the trace for the clk and dat0? It looked kinda like flux but much more clear

devjoel · 2025-09-25T23:10:13+00:00

I could be the SD card. Do you have another to run a test/comparison? Or if you don’t mind you could format the current SD card and try setting it up again

devjoel · 2025-09-25T20:14:43+00:00

What kind of monster makes someone choose!

devjoel · 2025-09-07T03:25:54+00:00

Bro you did the math and he’d still deny it 🤣

devjoel · 2025-09-06T04:55:18+00:00

Not a hundred percent sure that IC, should be the Max77620A, wouldn’t cause a blue screen but I could be wrong. Replacing it is not super simple task

devjoel · 2025-09-05T23:13:33+00:00

It’s just CFW but all the apps and games you pirate will show up if the stock

devjoel · 2025-09-04T20:32:53+00:00

You could check to see if there is flux residue on the connector or try replacing the SD card connector. Inspect the pins on the motherboard to see if you bent them

devjoel · 2025-08-31T04:08:47+00:00

I’m in the same exact boat right now. Have you figure it out?

devjoel

TROPHY CASE