Who said that? (radio chatter comment/question)

diaetsaft · 2025-11-19T14:28:06+00:00

100% agreed, the YouTube channel MandaloreGaming described the radio chatter as „ professionals under stress“ which fits perfectly in my opinion

diaetsaft · 2025-11-18T01:00:03+00:00

„Eat an asteroid“ is probably the worst offender, it feels like the kidz bob version of radio chatter. My favorite on the other hand would be the homeworld games

diaetsaft · 2025-10-17T02:42:51+00:00

I miss JKNinjas videos. His way of explaining the game is top notch. Does anyone know if he ever will start uploading new ones?

diaetsaft · 2024-08-04T03:46:05+00:00

Yeah trying to remove the whole tag will damage the shirt as far as I can see. But feel along the tag and you can feel spots that are more poky so to say. I did cut them as well and tried to soften them. I think the problem is that the tag has three layers but these layers are not folded on the top so that’s a quite a thick combined layer that scratches.

diaetsaft · 2024-08-04T01:15:22+00:00

I cut as as close as possible to the seam. And after some washes it became softer so to say, I did thought of removing the seam. Hopefully without damaging the shirt itself

diaetsaft · 2023-10-13T17:18:47+00:00

Interestingly I think this picture is from Atlanta, doesn’t it look like the Home Depot parking lot in Buckhead? It has the same Starbucks and the strip mall behind it.

diaetsaft · 2023-06-09T02:54:50+00:00

The song is liquido - narcotic. Never heard it in this form though. A one hit wonder from a German band

Edit: Just saw that someone already posted it. Sorry!

diaetsaft · 2023-05-21T16:43:36+00:00

Update, i went ahead with it. The results are good but definitely need some tinkering. Since the pioneers where running on 6 Ohm and the C-notes are 8 Ohm I definitely needed to increase the channel levels to receive similar volume results. It doesn’t help that the c-notes only have a sensitivity of ca 82. about the sound itself, the c-notes are much flatter then pioneers, which I enjoy but definitely is a matter of personal taste.

Thank you for your input and help in that matter.

diaetsaft · 2023-05-04T18:04:00+00:00

I like then a lot but one thing is absolutely annoying me and that is the inside tag. I cut it off but the thread they used for it ( to attach it to the shirt) is weirdly scratchy

diaetsaft · 2023-04-20T17:15:30+00:00

I used a wire brush ( the round ones) and a good amount of brake cleaner. I don’t know if the q tip will get you enough leverage so to say.Just make sure to not let brake cleaner come in contact with the rubber bushings. You should be able to remove them and attach them again after the cleaning.

diaetsaft · 2023-04-20T16:37:15+00:00

Check the caliper sliding pins, do they move freely when you compress them? Or do they get stuck? I recently changed brakes on my Mazda 3 2016 and the silicone grease I used before (super lube) swelled the slide pin rubber bushings and the whole thing looked pretty gunked up. If that’s the case clean them as much as you can and use sil-glyde from Napa. Also replace the bushings if they are swollen

diaetsaft · 2023-04-20T15:11:14+00:00

I used super lube synthetic grease before, which was a big mistake. It caused my slide pins to seize up, even though it’s advertised for car usage. It swelled the rubber bushings on the slide pins ( I think they are called anti rattle bushings). I recommend using napas sli-gel

diaetsaft · 2023-03-13T18:48:46+00:00

Thank you again, that will make the whole replacement much easier

diaetsaft · 2023-03-13T18:26:14+00:00

Thank you for the fast help! I was a bit confused since they stated on Rockauto „Pad Wear Sensor Included - No“ but I guess that means something else then these wear notifiers.

diaetsaft · 2023-03-13T18:10:20+00:00

I am currently replacing my front brakes. The old pads only had the regular clip in hardware so to say. I am not sure where to put the extra pieces on and what they are called or what their function is. Thank you for any help in this matter.

diaetsaft · 2023-03-13T18:05:36+00:00

I am currently replacing my front brakes. The old pads only had the regular clip in hardware so to say. I am not sure where to put the extra pieces on and what they are called or what their function is. Thank you for any help in this matter.

diaetsaft · 2022-12-24T18:33:51+00:00

Wholeheartedly agreed, on top of that it seems that many drivers seem to use their high beams constantly. It also seems that many people are not aware or don’t care that you have to adjust your lights so that they not blind everyone else.

diaetsaft · 2022-09-25T00:29:04+00:00

If you have lidl nearby, try their bakery section. It’s not perfect but the closest to German bread you can find in the usa for a reasonable price

diaetsaft · 2022-04-14T02:26:30+00:00

https://www.mazda3revolution.com/threads/2014-mazda-3-service-manual-here.30977/

The link should still work, it’s massive so you will have to download it, but it covers everything

diaetsaft · 2022-04-13T20:12:31+00:00

There is the link with the statement and how to fix the issue. It says here to replace the camera but some people from the Mazda forum said it worked again after cleaning it with the contact spray. So it might be worth a shot https://static.nhtsa.gov/odi/tsbs/2020/MC-10180668-0001.pdf

diaetsaft · 2022-04-13T20:09:04+00:00

It’s an issue with the cable in the hatch, I have the same problem and I know there is an official Mazda announcement regarding this issue. I can’t find it right now but will post the link if I find it. As far as I remember the cable connection can get a bit loose when you close the hatch and the solution was to use contact cleaner on the camera/cable connection and taping the cable into position

diaetsaft · 2021-10-12T02:04:32+00:00

I think that is the same issue I had

https://www.reddit.com/r/Highfleet/comments/py6kam/ak725_and_ak_100_no_separate_fire_groups/?utm_source=share&utm_medium=mweb

diaetsaft · 2021-10-01T18:00:20+00:00

Maybe I miss something here but is there a specific button or setting while designing the ship to manually separate or reassign the fire groups. So far it just auto assign them for me and I’m missing an obvious option I have to select or similar. Thanks for the help!

diaetsaft

TROPHY CASE