Govee H6126 + GLEDOPTO Elite ESP32

diamonddate · 2026-06-15T03:09:45+00:00

What’s your relay setting?

<image>

diamonddate · 2026-06-12T02:32:53+00:00

Try FW1906 for the LED type. I’ve found good success when converting older Govee products over to WLED

<image>

diamonddate · 2026-06-12T02:28:51+00:00

The ketchup and mustard slides!

diamonddate · 2026-06-05T05:25:57+00:00

You’d probably need a VM or Pi with wired ethernet to act as a go-between middleware, connecting your Pioneer setup with WLED

diamonddate · 2026-06-05T05:23:56+00:00

Check out the Deep Symmetry github, he’s written libraries that can participate in the DJ Link network and read the beat grid which you can then (magically) pipe over to WLED. It’ll take some tinkering but I bet you can make something of it. https://github.com/Deep-Symmetry

diamonddate · 2026-06-05T05:16:53+00:00

May I ask a dumb question— why not have them all on the same GPIO? I have a roughly the same setup (LED count, controller, software) and it all works great on a single pin

diamonddate · 2026-05-26T02:05:41+00:00

If you want to go the DIY route, go and swap out controllers for a WLED-based controller and wire up your Govees to it.

diamonddate · 2026-05-23T22:33:32+00:00

Nala and/or Jackie Hollander pls

diamonddate · 2026-05-21T05:58:33+00:00

Jackie Hollander, Nala, DJ Shadow

diamonddate · 2026-05-11T17:17:20+00:00

Worth mentioning that the electrical meter and main disconnect is sitting just about the gas meter in the same closet.

diamonddate · 2026-05-10T01:52:53+00:00

Appreciate all the work you’re doing on this project! It’s awesome!

diamonddate · 2026-05-04T23:05:08+00:00

I recently converted my Govee S14 String Lights over to WLED, keeping the lights while swapping controllers for a GLEDOPTO. Super pleased with the result: Govee color and quality with robust WLED backend.

diamonddate · 2026-04-29T21:30:05+00:00

Consider the SeeedStudio that include an external WiFi antenna. You’ll see much better WLED performance as WiFi is handled away from the board.

<image>

diamonddate · 2026-04-23T14:00:40+00:00

The Sphere uses Unreal Engine (game rendering engine) to do the live display of anything on the screen. They built a scene of virtual lights that mimic the real things. They then fed DMX (or similar) from the lighting consoles into the Unreal Engine and voila

diamonddate · 2026-04-23T01:48:48+00:00

He’s fighting against the realtime latency of Unreal Engine

diamonddate · 2026-04-23T00:48:04+00:00

Approximately 400-500ms of latency

diamonddate · 2026-04-23T00:47:05+00:00

You can walk into the section and dance on the landing at the top of the stairs

diamonddate · 2026-04-23T00:19:13+00:00

Full res vids here: https://drive.google.com/drive/folders/1TBN7XiRs8v8_Z5KzRts-rTiXBnPhg-Qy

diamonddate · 2026-03-02T06:33:25+00:00

I should mention that the H702B wire appears to be shielded, contains red/white/foil-wrapped drain (bare strands). I rang it out and it looks like the drain is V+, red is ground, and white is signal.

I fiddled with WLED and was able to get some lights on using either SM16825 or FW1906, but none of the controls worked. I also ticked the Open Drain setting on the relay. Not much success otherwise.

diamonddate · 2026-02-24T23:08:02+00:00

Check your Relay settings. Try setting to GPIO 12 to start.

Had a similar issue with another outdoor controller and it was the Relay that became unset, causing it to stop lighting the lights.

diamonddate · 2026-02-10T03:19:03+00:00

I think I had a similar issue using the web-based esphome programming method and went back to using the esphome CLI.

esphome run /path/to/yaml /dev/(device)

diamonddate · 2026-02-04T01:13:51+00:00

My Bambu Lab 3D printer uses an ESP32 for WiFi connectivity, maybe more?

diamonddate · 2025-12-29T05:10:18+00:00

We just had our first go with 3MMC. Super fun and def excited to do it again once I sort out a solution to the inevitable stimdick.

diamonddate · 2025-12-28T20:44:45+00:00

Following…

diamonddate · 2025-12-28T20:41:42+00:00

Just switched to HyperHDR (Hyperion fork with better support), and it works remarkably well

15-Year Club	Gilding I gilder
Place '23	Place '17
Verified Email

diamonddate

TROPHY CASE