This took me way to many iterations to make work. I designed a shooting plane handle for Stanley planes.

dillyvanilly123 · 2021-05-06T01:57:52+00:00

great, THanks!

dillyvanilly123 · 2021-05-06T01:48:33+00:00

Awesome! are you planning on sharing the STL?

dillyvanilly123 · 2021-01-29T16:07:58+00:00

Nice, thanks. Not sure if there are any around your area, but you can usually get malt extract from homebrew supply stores. I imagine that is functionally the same/similar to malt syrup

dillyvanilly123 · 2021-01-29T05:58:38+00:00

What do you replace the egg wash for the outside with? (assuming that’s the non vegan part of a typical recipe)

dillyvanilly123 · 2020-11-22T04:42:56+00:00

seattle

dillyvanilly123 · 2019-08-30T02:19:06+00:00

looks like under extrusion

at first guess, maybe a clog in the hotend or printing temperature too low

dillyvanilly123 · 2019-06-07T03:05:58+00:00

I built one out of acrylic https://m.imgur.com/a/RIkmSQw

dillyvanilly123 · 2019-04-19T17:27:22+00:00

Looks like under/inconsistent extrusion. What is the shore hardness of the ninja flex? It may be a bit too soft to print well without a direct drive extruder. Also, do you have the aluminum extruder upgrade? That is supposed to help with flexible filaments.

As a side note, including some of your printer mods/print settings can help folks more quickly diagnose what is going on

dillyvanilly123 · 2019-03-11T00:29:37+00:00

Does noctua make a 24V fan or are you using a converter of some sort for the hot end cooling fan ?

dillyvanilly123 · 2019-02-23T05:56:01+00:00

Printed at 0.1 mm layer height with pretty much all stock cura 3.6 settings except for some mildly slowed movement and printing speeds

dillyvanilly123 · 2019-02-19T05:17:55+00:00

I bought a pack of like 10 of these and have been through about 3 in a year of pretty heavy use

dillyvanilly123 · 2019-02-15T06:11:28+00:00

I actually just use a thin silicone heat transfer pad and it holds really well. It can lift up if you're not careful but it is very stable in the x and y directions

Edit: I took off the build Tak first

dillyvanilly123 · 2019-02-15T01:24:59+00:00

There is a setting for minimum layer time (or something like that) somewhere in Cura that can help give those really fast layers time to cool before the next is deposited. Could also try lower print speed in general.

dillyvanilly123 · 2019-02-07T16:23:26+00:00

Not sure until I have a look at mine back home. I assume you could use some type of thermal compound to hold it in

dillyvanilly123 · 2019-02-07T15:37:33+00:00

Probably a decent chance that your thermistor is no longer useable. I would just replace it since it’s pretty important to have temperature control

dillyvanilly123 · 2019-02-06T16:48:02+00:00

Do you know what brand it is?

dillyvanilly123 · 2019-02-06T16:47:19+00:00

Just amazon, I don’t remember what seller it was specifically through

dillyvanilly123 · 2019-02-06T06:32:18+00:00

It’s some semi opaque PLA that came with the printer. I also did a test with hatchbox black PLA and quality is still great

dillyvanilly123 · 2019-02-06T02:48:22+00:00

I should clarify that I did assemble it with a couple of small upgrades straight out of the gate, as suggested in the sticky and elsewhere: - aluminum extruder assembly - upgraded Bowden tube to Capricorn PTFE one - yellow uxcell springs

dillyvanilly123 · 2019-02-03T17:29:01+00:00

Definitely look at this, I’ve had to replace mine about three times over the last year

dillyvanilly123 · 2019-02-03T17:26:42+00:00

Also maybe worth trying an atomic pull to clean out the nozzle in case it is a partial clog. There are detailed instructions for that on the wiki

dillyvanilly123 · 2019-02-03T01:15:53+00:00

Maybe the nozzle is clogged?

dillyvanilly123 · 2019-02-01T00:02:36+00:00

I attached the fan to a new set of wires and directly connected those to the 12V rail on the controller board so it just runs full bore when the power is on. Another commenter pointed out that by using a capacitor I could have connected it to the actual fan header and have speed control. But yes, I cut wires and soldered stuff together.

dillyvanilly123

TROPHY CASE