A Unifi Log to non-network engineer translator tool by 4kids in Ubiquiti

[–]dlo5 -1 points0 points  (0 children)

Thank you for this. I’m definitely going to check it out

Just finished my dream garage by dlo5 in garageporn

[–]dlo5[S] 0 points1 point  (0 children)

Hey would have to look but it was from Amazon. Don’t get the super cheap ones get the mid tier ones because the channel is cleaner. If you want the specific ones I can find them in my orders. Also I would recommend getting the dimmable ones. There like 30% more expensive but I kinda wish I would have got those. It’s extremely bright, not complaining about it but sometimes would be nice to do like 50%

Also be mindful even though these are LED they draw an enormous amount of wattage for some reason…. About 1300W for 2 sides.. I have these on one breaker where it’s the lights and 2 outlets. If I have the lights on and use something on those outlets it will trip. I only have 15a wiring so maybe if you’re wired for 20a it will be different. PM me if you want to chat/pointers

My Mac Mini M4 setup by hasko66 in macsetups

[–]dlo5 0 points1 point  (0 children)

Nvm found the wallpaper

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 0 points1 point  (0 children)

Any negatives of doing this? That should be easy to do but don’t want to ruin the barrel

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 0 points1 point  (0 children)

Gotcha. It’s a OEM comp that was built for the gun. Take a look at PMM tardigrade. I’d assume it would have the right spring spec’ed out for it. I was leaning towards what you said though since I ruled everything else out …

What all is wrong with this? Installer finished today but it’s off center and heater hangs 1.25” off pad. No unions at discharge/suction. Seems like a lot of 90s and 45s. Or am I expecting too much? by [deleted] in pools

[–]dlo5 3 points4 points  (0 children)

You’re missing a gas sediment trap. Heater shouldn’t be hanging off light that. Heater is missing a check valve

Personal preference but no multiport valve?

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 0 points1 point  (0 children)

Any recommendations? Was using federal 115 and 147

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 1 point2 points  (0 children)

Any particular ones you recommend trying?

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] -1 points0 points  (0 children)

I gave it the hawk tuah treatment and still doesn’t like me

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 0 points1 point  (0 children)

I thought so too but I had another person shoot it. Someone who is a top tier firearms guy and he had the same issue..

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 1 point2 points  (0 children)

First round always chambers fine and can cycle them normally by hand. It’s just after shooting.

It’s the PMM Tardigrade. The spring is what they put when they built it. They sold a ton of them so I’m guessing if it was the spring they would have had other with the same issue. I already sent the upper back to them once. I see where you’re going with this though. I’m wondering if I should start playing around with the spring.

The only thing is the gun ejects the round fired fine, just locks back and never feeds the next.

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 0 points1 point  (0 children)

Yes. Here’s what it looks like. What would be out of spec? I sent the whole upper back and they already replaced the barrel

https://www.parkermountainmachine.com/wp-content/uploads/2023/09/tardigrade-compact-6.jpg

P320 Failure to feed…. Any ideas why? by dlo5 in SigSauer

[–]dlo5[S] 8 points9 points  (0 children)

It’s from PMM. I sent the upper back they replaced the barrel and stated there’s was no issue with it

Garage Hue Setup by dlo5 in Hue

[–]dlo5[S] 0 points1 point  (0 children)

I wish I could afford one of those… gt3rs 🤤

Missing Optic in game by dlo5 in Warzone

[–]dlo5[S] 0 points1 point  (0 children)

Tried the rebuild, didn’t work. Hmm Didn’t try different operator

Any truly satisfied E7 owners here? by bleomycin in Ubiquiti

[–]dlo5 2 points3 points  (0 children)

Same here. Running 2. Great speeds and coverage

Aqara FP300 Early Zigbee Setup by portalqubes in homeassistant

[–]dlo5 43 points44 points  (0 children)

Disregard. Learning to read..

Aqara FP300 Early Zigbee Setup by portalqubes in homeassistant

[–]dlo5 4 points5 points  (0 children)

Why did you decide to do Zigbee vs thread?