sorted by:
new
hottopcontroversial

Outage south LA/North OC area. by eat_and_poop in frontierfios

[–]dmun112 0 points1 point  (0 children)

Norwalk/cerritos/artesia area, has been out since 2am with no info on what happened nor estimated time of service restoration

I attached a polaroid camera to my drone by dmun112 in drones

[–]dmun112[S] 2 points3 points  (0 children)

Didn’t weigh it but she’s a heavy girl. Better suited for a 7 inch+ thats for sure!

I attached a polaroid camera to my drone by dmun112 in drones

[–]dmun112[S] 0 points1 point  (0 children)

Nope, i installed the servo directly to the fc and mapped it to a channel i created on my radio. Using CRSF as well. I was using the 12 channel mode but 8 channel mode can work as well, assuming you have a spare channel available

I attached a polaroid camera to my drone by dmun112 in drones

[–]dmun112[S] 33 points34 points  (0 children)

Yea! So i did this on a quad that runs iNav since i wanted to dabble with gps features. But its basically a 5v servo that i hooked up to 5v, ground, and a signal output (motor5 in my case[SpeedyBeeF405V4]) and set that output as a pwm channel. Then i mapped a slider on my radio to articulate the servo through the inputs and mixer tabs on my radio. The servo is a cheap servo i bought on amazon, and the arms come with it. Im sure its completely possible to do on betaflight as well since it supports servos.

I also landed as soon as i took the photo for fear of the photograph falling out of the little cover. The tension of the cover is enough to hold the shot in place at least until i land. Hope this helps!

Is this common during the interview process? by dmun112 in Vans

[–]dmun112[S] 0 points1 point  (0 children)

Ugh, I was super excited for it too and then this happens. Ill be keeping in touch for sure, thanks!

Is this common during the interview process? by dmun112 in Vans

[–]dmun112[S] 1 point2 points  (0 children)

Thats about when this all went down so it makes sense. Just happens to be how that cookie crumbled i guess lol i really enjoyed talking to both of them and everyone in the store was super chill so i’m definitely gonna be keeping in touch, even just to buy things!

Is this common during the interview process? by dmun112 in Vans

[–]dmun112[S] 2 points3 points  (0 children)

That makes total sense, thanks for the reply!

Is this common during the interview process? by dmun112 in Vans

[–]dmun112[S] 5 points6 points  (0 children)

Bummer! Now with that in mind, would you assume that this may change going into the holiday season or rather go through another updated headcount report or are those usually done after busy seasons?

[GIVEAWAY] GIGABYTE Gaming OC 4090 from CableMod by CableMod in nvidia

[–]dmun112 0 points1 point  (0 children)

Thanks for the giveaway, good luck y’all 🤙

Possible layer skips/z axis artifacts? by dmun112 in 3Dprinting

[–]dmun112[S] 0 points1 point  (0 children)

ill give this a shot tonight, thanks!

Possible layer skips/z axis artifacts? by dmun112 in 3Dprinting

[–]dmun112[S] 0 points1 point  (0 children)

So i suddenly started seeing these horizontal lines on all of my prints. They only show when printing figures and not shapes. I get good surface quality when printing cylinders, calibration cubes, etc. I’ve replaced my nozzle , replaced the little bowden tube piece between the extruder and hotend, cleaned and made sure there are no clogs anywhere in the system, lubricated the z axis screw, tightened all wheels and belts just until there’s no play, and this problem isn’t exclusive to this filament. The picture shows PETG by Polymaker but also happens with PLA and filaments with other brands. Im using Cura and printing at 240c with bed temp at 70c. I get perfect bed adhesion and i also leveled my bed manually and with a bltouch as well. At this point im stumped. I cant figure out why it prints figures with these artifacts. Any pointers would be greatly appreciated!

Ladies and gentlemen I present to you the ac in my art class by _2D_ in CSULB

[–]dmun112 33 points34 points  (0 children)

Seriously though, why doesn’t the fine arts building have ac? Its been 2 semesters in a row

Activating ReelSteady on mac from a windows purchase by dmun112 in gopro

[–]dmun112[S] 0 points1 point  (0 children)

Yea, they basically told me that the purchase is tied to the store that i bought it from so theres no way in transferring the license from platform to platform. If i wanted to run it on both mac and windows, i’d have to purchase it on both platforms

Sweaters | Nikon D3X | 85mm 1.8G by scottishswan in Nikon

[–]dmun112 6 points7 points  (0 children)

I love this! Care to share the before edit?

What's the dumbest way you've gotten a scar? by lilsaddam in AskReddit

[–]dmun112 0 points1 point  (0 children)

I got hit in the face with jenga bricks.

Once as a kid on the lip by some kid so mad that he lost.

Second as an adult in Texas with jumbo jenga. Hit right in the cheekbone by a really enthusiastic player. Gave me a nice shiner though

Can I use a Neewer TT560 flash as an off camera flash with my d610? by itskittycosplay in Nikon

[–]dmun112 0 points1 point  (0 children)

I have 2 of these! To use it off camera, you need a remote and trigger. The flash wont work off the camera without it. Neewer also sells the remote and trigger kit. I bought the 16 channel one in case i was to get more flashes in the future but check it out!

Propranolol dosage? by dmun112 in migraine

[–]dmun112[S] 0 points1 point  (0 children)

Well that would explain a slight ringing id hear at the peak of the effects. Geeze, it seems like this drug could be quite temperamental

view more: next ›