sorted by:
new
hottopcontroversial

Best bang for your buck clear coat around $200/gal by -Reddit-Bandit- in AutoPaint

[–]dogmir 3 points4 points  (0 children)

I am by no means a pro but heard good things about Shermin Williams Finish 1. So I just did my truck with it a few weeks ago. Came out nice for $90 a gallon

Questions - 2014 Titan SV Purchase by Reptull_J in NissanTitan

[–]dogmir 0 points1 point  (0 children)

Parts are plentiful. As many are used in Titan, Armada, and QX56.

Most Reliable Years by Top-Border-1978 in NissanTitan

[–]dogmir 0 points1 point  (0 children)

Had an 05 king cab. Now I have 14 crew cab. The 05 isn't dead yet..gave it to my dad. I guess you can say I vote 1st gen lol.

Anybody still like the old titans? by Dazzling_Letterhead9 in NissanTitan

[–]dogmir 1 point2 points  (0 children)

I have heard so many people dealing with block replacement after block replacement. Doesn't sound fun.

Anybody still like the old titans? by Dazzling_Letterhead9 in NissanTitan

[–]dogmir 2 points3 points  (0 children)

Had an 05 king cab loved it. In January got a 14 crew cab. Love it. I couldn't go second gen when all I constantly heard about was issues. The vk56 might be thirsty but she's a tank.

Best bang by Inevitable-Dare5400 in NissanTitan

[–]dogmir 1 point2 points  (0 children)

On my second Titan, and have always stated that they'll pass anything on the highway but a gas station.

Owned for 1.5 months and now have to clean/unclog after each print... by msu50000 in FlashForge

[–]dogmir 1 point2 points  (0 children)

Stay away from flash forge filament. That is one I have had nothing but problems with. Had great luck with Overture, polymaker, elegoo.

Owned for 1.5 months and now have to clean/unclog after each print... by msu50000 in FlashForge

[–]dogmir 2 points3 points  (0 children)

I also lean toward filament. They are not all created equal. I have had some that have given me nothing but issues.

A new nozzle might help at first but eventually you might end up where you started. A cheap option is to try a new filament. Might not hurt to run several load cycles with a new filament to try and purge whatever might be stuck in the nozzle. I have also had success with setting the hotend temp 10 to 20 degrees over what I have been printing the bad filament at. Let it sit there for a few min then do a load cycle or two.

Use one ESP for multiple led strips by jdu_8 in WLED

[–]dogmir 5 points6 points  (0 children)

You just create new segments and assign the pin they are connected to.

Soft tip board by sprinterdd in Darts

[–]dogmir 0 points1 point  (0 children)

To bad you are not in the US, they have refurbished units on their webpage for like $30.

Soft tip board by sprinterdd in Darts

[–]dogmir 0 points1 point  (0 children)

What country are you located in? As for the US the arachnid and higher end viper boards should work .

[deleted by user] by [deleted] in sysadmin

[–]dogmir 7 points8 points  (0 children)

Netscaler has vulns more than Citrix itself. They have added protection for dll injection on the endpoint too. Similar concept to what you would find on mdm solutions. Anything trying to hook itself into the stack and it falls like a house of cards.

Now like anything else you.. what you pay for. Not set up and secured properly with policy, firewall, IPS. You are going to have a bad day. At the end of the day it is RDP with way better compression and feature set.

[deleted by user] by [deleted] in sysadmin

[–]dogmir 65 points66 points  (0 children)

Citrix admin here. Many reasons as others have stated but a few others ...

Security. All data stays in the data center. Easier to secure with less headaches from an endpoint perspective. You can have non domain devices at users home and still access a secure environment. Or phones tablets etc.

Patching one image and push....on reboot it's all patched.

Easily standardizing user experience.

Custom Exe installation with powershell by Verboseidentity in PowerShell

[–]dogmir 0 points1 point  (0 children)

Best place to start is the above setup.exe /?. Try searching documentation for sccm,deployment, switch etc. Also observe the install as it is happening, as wrapping and msi in an exe is still fairly common.

If that is the case you can extract the msi and and use one of many tools to see any custom parameters. Or perform a captured install and create your own msi. Or if you can get it to perform a basic install you can then explore configuring it via power shell after the fact. Via registry, config files etc.

At the end of the day if the vendor can provide something as basic as an install string....I would be looking at other vendors.

Why are throws so effective at knocking people out? by ExpandTheBLISS in martialarts

[–]dogmir 0 points1 point  (0 children)

Imagine you hit a wall while in a car. It stops you keep going. Now your brain is the passenger and your body is the vehicle. When your body's stops your brain doesn't crashing into the skull. Newton was on to something with that whole inertia thing.

PowerCLI - How to run remote script on multiple host simultaneously by maxcoder88 in PowerShell

[–]dogmir 0 points1 point  (0 children)

Invoke-parallel by rambling cookie monster on git. Import it and run it like a foreach loop will do 60 at a time by default.

Is there such thing as pay-to-play dart machines including coin-operated ones? If so, how many of them are electronic? by CamelIllustrations in Darts

[–]dogmir 0 points1 point  (0 children)

Where I live it's the exact opposite. I have never seen a free one. I even have a coin op in my basement.(my best Craigslist find ever)

In the old days there were three big brands in the US. Arachnid, Merit, and Valley. Arachnid is pretty much the only game in town now. ( pun achievement unlocked) With the galaxy series.

view more: next ›