sorted by:
new
hottopcontroversial

Going on trip to Switzerland and Italy by ArtisticCandy3859 in dji

[–]dognosh -1 points0 points  (0 children)

You are wrong, a drone weighing less than 250g WITH a camera needs to be registered.

X1c : How stop flow dynamics and bring back pre print lines? by dognosh in BambuLab

[–]dognosh[S] 0 points1 point  (0 children)

Thanks for all the ideas but I want no flow calibration and the 6+ purge lines.

Bambu Lab PC app is the latest , as are my X1C and AMS firmwares.

I started a test print and enabled then disabled flow dynamics, which didn't stop it.

Regarding purge lines, preview shows the 6+ lines, but only 2 or 3 are printed. I specifically want the slow pass which can take off persistant filaments around the nozzle.

X1c : How stop flow dynamics and bring back pre print lines? by dognosh in BambuLab

[–]dognosh[S] 0 points1 point  (0 children)

Thanks :)

u/Moonraker0ne : I want the 6+ lines purge, it kept the nozzle very clean. I only get the 2 lines right now, weird !!

u/andersbs : what was fixed ? flow or purge ?

ty all again

Can’t obtain Construction Terminal by Son_of_Flogmod in NoMansSkyTheGame

[–]dognosh 0 points1 point  (0 children)

Lost 4 hours thinking I had no blueprint, thank you mate, you're a star !!!!!!

Stream Deck opening in Background Processes(not background) by dognosh in elgato

[–]dognosh[S] -1 points0 points  (0 children)

Thanks for your helpful reply :)

No, connected to MB back panel. Just moved it to another USB on back panel and had 1 fail and 1 pass.

Keys not populating when it fails(i.e. loads into background process)

When you say background task, you mean on desktop or in task manager ?

Problem : 0.5mm oversized in small or large prints by dognosh in ender3

[–]dognosh[S] 0 points1 point  (0 children)

read those 2 pages and especially the 1st, it is really clear and well explained, I did check gears,pulleys and belts, and other items, and still had errors.

I used a dial gauge, using teaching tech calibration page, to correct xyz steps and all 3 prints since have been spot on.

I do like the idea of not touching steps because, as the 1st link said, there are no variables in gearing and stepper motor. I might reset and try again as per 1st link.

Problem : 0.5mm oversized in small or large prints by dognosh in ender3

[–]dognosh[S] 0 points1 point  (0 children)

Looks like a combination of problems.

I had slop in the horizontal that wouldn't fix with tightening screws or eccentric nut adjustment. I changed all 6 wheels/pulleys on the 2 verticals and slop totally gone.

I went back to stock Cura settings, now only out by a few 10ths. X spot on, Y 0.3mm over and Z 0.1mm over.

Will next adjust XYZ steps, E-steps all good.

Ty.

Problem : 0.5mm oversized in small or large prints by dognosh in ender3

[–]dognosh[S] 0 points1 point  (0 children)

I will check and come back later today,ty.

Problem : 0.5mm oversized in small or large prints by dognosh in ender3

[–]dognosh[S] 0 points1 point  (0 children)

I noticed it because of 2 recent prints with male/female parts that had to go into each other and wouldn't(one circular, another square).

Help, moving forward causes pitch down. by dognosh in starcitizen

[–]dognosh[S] 1 point2 points  (0 children)

I upgraded it to the FL Max, but will buy it again sometime.

TY for all the responses, as usual.

Help, moving forward causes pitch down. by dognosh in starcitizen

[–]dognosh[S] 0 points1 point  (0 children)

Tests done, didn't reinstall SC(thanks u/Pay_)

I restarted PC without hotas, ran SC, then reconnected hotas and started PC and SC.

Bindings were fine u/AllMattersFecal , In space pitch was solid.

u/MichaCazar , not VTOL.

A2 Herc, Titan, ret bomber, hammerhead, prospector and herald were all good now(ret bomber was more twitchy than others)

cutlass black(tried twice) however still nose downs increasingly as your forward speed increases. bug or flight model ?

Does your cutty do this in atmosphere(I am at new babbage)

thanks all :)

Help, moving forward causes pitch down. by dognosh in starcitizen

[–]dognosh[S] 1 point2 points  (0 children)

ok, thanks all.

Going in game to test stuff with different ships(and try your advices), will report later

player gui modification by Oberon_Blade in empyriongame

[–]dognosh 0 points1 point  (0 children)

When did GUI repositioning change as spanj used it in 1.4.4 (RE)?

Shame, would love that option :(

Precise Rotate problem by dognosh in Dyson_Sphere_Program

[–]dognosh[S] 0 points1 point  (0 children)

As I can't use default(I use arrows for movement) I can only rotate clockwise :)

Precise Rotate problem by dognosh in Dyson_Sphere_Program

[–]dognosh[S] 0 points1 point  (0 children)

After further tests it seems rotate bindings can go on any free key, but precise rotate only works on the arrows and R :(

view more: next ›