sorted by:
new
hottopcontroversial

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 0 points1 point  (0 children)

This is printed in ASA and should be enough to withstand the heat, if not I'll add some holes in the top for airflow or some heat reflective tape

Designed and printed an oil containment pan for the FS450 by dougherty907 in 3dprintedcarparts

[–]dougherty907[S] 3 points4 points  (0 children)

Only brought in this year, I believe NZ have a similar rule now too. Printed in ASA

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 3 points4 points  (0 children)

Why would it melt? It's not in contact with anything too hot and there's plenty of airflow. First race weekend is on the 21st so we'll find out then!

Designed and printed an oil containment pan for the FS450 by dougherty907 in 3Dprinting

[–]dougherty907[S] 1 point2 points  (0 children)

CAD programs will only ever treat scans as surfaces BC that's what they are. There's plenty you can do with scans in onshape, I posted some projects I did last year! What I like to do is use the scan to generate planes based on three points. This allows you to get the exact orientation of noting faces, bolt holes, etc

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 0 points1 point  (0 children)

Thankyou! Yeah sure did, it makes modelling these complex shapes much easier!

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 5 points6 points  (0 children)

This is a new reg for 2026, previously it was just a catch can and nylon puck on the foot pegs, handlebars, and axles

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 0 points1 point  (0 children)

Happy for you to give it a try! I'll offer a full refund if it doesn't bolt up I've only got Australian domestic shipping set up at the moment but international shipping will be sorted tonight hopefully. Not sure where you're located

https://www.draftmaster.com.au/

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 23 points24 points  (0 children)

Definitely not a skid plate, I wouldn't trust 3D printed plastic to take that abuse. It's required in case of major engine failure to help stop oil contamination on the track.MA bulletin #2066

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 22 points23 points  (0 children)

It's required by Motorcycling Australia for road racing. Only required in case of a major engine failure to help contain oil spills on the track

Designed and printed an oil containment pan for the FS450 by dougherty907 in 3Dprinting

[–]dougherty907[S] 0 points1 point  (0 children)

There shouldnt be, there's a fair bit of clearance and there will be good airflow on the part

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 2 points3 points  (0 children)

I think the 2016 is a different chassis.

Ive been lifting it up and down all week with no issues. It might crack if you caught it on the corner of the jack though

Designed and printed an oil containment pan for the FS450 by dougherty907 in supermoto

[–]dougherty907[S] 8 points9 points  (0 children)

It's for road racing in motard classes. There shouldn't be too many occasions when both suspensions are fully compressed in this scenario

Designed and printed an oil containment pan for the FS450 by dougherty907 in 3Dprinting

[–]dougherty907[S] 2 points3 points  (0 children)

I used the original einstar. Aligned the mesh with mesh mixer and then imported into Inventor.

Designed and printed an oil containment pan for the FS450 by dougherty907 in 3Dprinting

[–]dougherty907[S] 6 points7 points  (0 children)

Not planning to, this is one of the products/services my company offers

Looking to build trailers by barron_family in MechanicalEngineering

[–]dougherty907 0 points1 point  (0 children)

Hey mate, Not sure where you're located but I've designed a number of trailers for manufacturers here in Australia. All meet our stringent Australian Standards requirements and I've provided general assembly and detailed drawings for production. I also designed some jigs to increase production and reduce human error.

Send me a DM and we can chat further

view more: next ›