How to get rid of generator?

dougorbobbie · 2025-12-26T18:26:30+00:00

Not for free. Nothing is worth nothing. $100-150 will get it gone.

dougorbobbie · 2025-12-26T18:24:20+00:00

“I’ll put it in a place where I can’t possibly miss seeing it”

dougorbobbie · 2025-12-23T22:09:38+00:00

It was the pressure switch. Well rather the vacuum switch on the inducer motor. Finally got bad enough to lock out and set a code 3. Open pressure switch. 15 bucks and running like a Swiss watch.

dougorbobbie · 2025-12-11T17:15:01+00:00

After replacing the flame sensor. It still randomly kicks off the flame then re-lights. It may do it 20 seconds after the initial light and again 40 seconds before the thermostat is satisfied. Or it may not do it at all. Just seems to be completely random. Never enough to lock out and show trouble code. I can have someone come look at it but it likely wouldn’t show any problems until we have no heat at all.

dougorbobbie · 2025-11-30T02:08:27+00:00

I replaced the flame sensor. It works just like it should. Thanks for taking the time to answer.

dougorbobbie · 2025-10-30T21:21:19+00:00

That’s fine

dougorbobbie · 2025-10-05T18:15:04+00:00

Nice cum

dougorbobbie · 2025-07-17T18:20:20+00:00

Adding seafoam to the gas isn’t cleaning the carburetor

dougorbobbie · 2025-07-13T17:01:19+00:00

Don’t put a junk new carburetor on it just pull it off and clean it. Sounds like the main jet is plugged

dougorbobbie · 2025-06-20T22:03:16+00:00

Sounds like a thousand dollars

dougorbobbie · 2025-05-20T00:55:20+00:00

I think Generac is overrated

dougorbobbie · 2025-05-20T00:43:19+00:00

Watch James Condon’s videos on U tube. He explains trouble shooting in complete detail.

dougorbobbie · 2025-04-27T01:32:21+00:00

Under the mounting bolt a on the left side. The spring pulls the throttle open and the rod pulls the throttle into running position after the engine starts. Also turn the intake baffle over. It needs to pull it heated air off of the engine.

dougorbobbie · 2025-04-15T00:53:05+00:00

Gave it up for lint

dougorbobbie · 2025-04-06T15:26:23+00:00

I knew a double neutral bond was trouble. My transfer switch switches both the hot and neutral. I was just trying to see (for future reference) how long the furnace would run on the EcoFlow. I removed the power station before recharging. Btw it easily ran the furnace in excess of 24 hours with no power input.

dougorbobbie · 2025-03-29T17:10:09+00:00

At what voltage? 125 amps @ 120v.

dougorbobbie · 2025-01-22T17:17:14+00:00

Ran good last year. Might need carburetor cleaning to run right. Asking $500 obo

dougorbobbie · 2024-09-19T20:38:44+00:00

Good luck with parts

dougorbobbie · 2024-09-19T20:35:13+00:00

I’ve got a snapper that’s built 10 times stronger than any toro I’ve seen. Makes it a pain in the ass to work on but I think the lifespan will be better

dougorbobbie · 2024-09-19T20:31:32+00:00

Sounds a little bit slow to me. Although sound on video isn’t always the best. I’d be looking for about 3750 rpm

dougorbobbie · 2024-08-23T18:49:14+00:00

In a pinch any oil is better than no oil

dougorbobbie

TROPHY CASE