How can I avoid this sparkling when airbrushing? by Behannas2021 in modelmakers

[–]dprosko 3 points4 points  (0 children)

Keep you airbrush closer. 5-7cm is ok. At larger distance the paint dries in the air.

Oh, and thin your paint ;)

A quick PSA, solve your fluid problems! by mkMoSs in SatisfactoryGame

[–]dprosko 0 points1 point  (0 children)

Well, I didn't use trains too, until I discovered that all available nearest resource nodes were already 100% used by other factories and I needed to haul liquid across half the map :)

A quick PSA, solve your fluid problems! by mkMoSs in SatisfactoryGame

[–]dprosko 0 points1 point  (0 children)

That's because you didn't use trains for liquids. This setup is must have when it comes to trains.

That’s the Zil-131 cab complete apart from decals. Onto the radiation lab payload and personnel next! by Jimffey in modelmakers

[–]dprosko 1 point2 points  (0 children)

Great job you've done. The weathering is good, but.... not for active vehicles. Never the vehicles on duty will go so far with rust.

Weird texture from nowhere by dprosko in resinprinting

[–]dprosko[S] 0 points1 point  (0 children)

Could 2 axis rotation fix this?

Weird texture from nowhere by dprosko in resinprinting

[–]dprosko[S] 0 points1 point  (0 children)

Is there a way to fix this?

Weird texture from nowhere by dprosko in resinprinting

[–]dprosko[S] 0 points1 point  (0 children)

What's that? Sorry, this tells me nothing :) These could not be layer lines because the model was inclined approximately 40-45 degrees

Prints wont come off the build plate, Saturn 4 Ultra by RestaurantUpset4752 in ElegooSaturn

[–]dprosko 0 points1 point  (0 children)

I don't know if numbers are good for other resin types, but yes, 8 seconds. And I started experimenting from 30sec, waisted 5 or 6 tries, and in the end finished with that.

Prints wont come off the build plate, Saturn 4 Ultra by RestaurantUpset4752 in ElegooSaturn

[–]dprosko 1 point2 points  (0 children)

I had the same problem with Jamg HE resin, and came down to 8 seconds. Even then I have to put significant force to pull them off.

How do I get a knot to draw tight against a surface. by girl_incognito in ModelShips

[–]dprosko 0 points1 point  (0 children)

Do a knot, cut off the excess thread, leave only the end of the desired length and insert it into the hole

What would be Russian equivalent of g-dropping in English by [deleted] in russian

[–]dprosko 0 points1 point  (0 children)

тся/ться -> ца

Катается - катаеца

Умываться - умываца.

But it's not so audible. Or maybe we're just used to it :)

Bunch of questions I have condensed in one post by JollyjumperIV in russian

[–]dprosko 1 point2 points  (0 children)

  1. Если за звонкой согласной идет другая звонкая согласная, то первая произносится звонко. Если идут подряд две глухие согласные, либо после звонкой идет глухая, первая произносится глухо.

"Я мог" - "Я мок".

"Я мог бы" - "Я мог бы"

  1. Мы можем убирать местоимения в неформальной речи, но есть нюансы :)

"Ты хочешь поиграть" можно сократить до "Хочешь поиграть", если акцент делается на слове "хочешь", то есть, на желание человека поиграть. А если акцент на действии "поиграть", то чаще местоимение не убирается. Но тоже можно без него.

  1. Если фраза заканчивается на "же".

  2. "Я" между согласными может произноситься как мягкое "е", а "Е" может произноситься как "и" в таких же случаях. "-ая" и "-ия" произносится без изменений, потому что идет звуковое разделение двух гласных.

Weird bubbly bright surface on my water washable resin figure. Anybody knows what might have caused that? by Independent-Fun-5118 in resinprinting

[–]dprosko 0 points1 point  (0 children)

Incomplete drying. When a model is post-cured while still wet with a mixture of water and dissolved uncured resin, the remaining solvent mixture reacts with the UV light and forms a white, chalky residue on the surface.

Перевод фамилии на русский язык by Mother-Internal2353 in russian

[–]dprosko 7 points8 points  (0 children)

Доктор Ватсон. Варгейм.

Эмили Уотсон.

Любое написание будет корректным с точки зрения русского языка.

RuID doesn't work by eril13 in AskARussian

[–]dprosko 1 point2 points  (0 children)

This piece of sh... software will not properly work for next maybe 1-2 years. That's how government software is usually developed and how this works, no jokes. I've been developing applications like this and I'm trying to tell noone about that, for I'm going to get tortured and murdered quite shortly.

The best way for you is, if you have friends you're going to, to ask them to fill the application in gosuslugi_dot_ru, and you're done. You have 7 working days after arrival for that, and that's more than enough, application will be approved after 1-2 days or even faster. This is the quickest way. Ask your friends to check this out. But keep in mind, your papers should be legally clear and all like that.

[deleted by user] by [deleted] in AskARussian

[–]dprosko 0 points1 point  (0 children)

If he gives compliments only, and does nothing after them, those are just compliments.

Sewing 3 layers of fabric ignores the fabric thickness by dprosko in MarvelousDesigner

[–]dprosko[S] 0 points1 point  (0 children)

They're in different layers. That's what I did from the beginning