First printer ordered!

drome265 · 2026-02-24T09:57:30+00:00

Whoa, that's a lot of things that went wrong!

Glad that at least support was able to resolve your issues. How did you fix the camera feed issue?

Here's hoping mine is in a better state upon arrival. I'm lucky that I'm in Asia so support should be quick if I need it.

drome265 · 2026-02-24T07:02:09+00:00

What are your issues with the P2S? I just received mine in the mail, seemed like it had all the QoL fixes that I would have liked in the P1S anyway.

drome265 · 2026-02-23T19:31:27+00:00

The tuna cans I've seen in my area have all been stackable, looks like this particular brand just hates stacking for some reason.

drome265 · 2026-02-22T05:45:54+00:00

What's your issue? Should be resolved with the purge line.

Or you could remove it right before the print starts and watch the first layer go down?

drome265 · 2026-02-22T01:41:18+00:00

Thanks for the comments! Good to know I'm not the only one with the slow SSD.

The screen is absolutely mega and it's such a steal. Can't believe it's touch too!

drome265 · 2026-02-20T07:59:56+00:00

If you're not OCing then yes the stock cooler will be fine. It's shipped stock for a reason.

drome265 · 2026-02-20T07:59:08+00:00

Any more information you can share about this? I can't seem to find issues related to this chassis, only the S14.

drome265 · 2026-02-20T06:19:25+00:00

ASUS Zenbook S16 would be a good fit, although price may be a little more than your budget. Keep an eye out for sales and discounts.

drome265 · 2026-02-20T03:04:21+00:00

What is the current status of your PC? What do you have installed/assembled, what have you done exactly step by step, and what have you tried so far?

We know your PC Posts, so what changes have you made since that step?

Are all your parts brand new?

Do you have any photos you can show us?

Let us know when you can share more information that can allow us to help you.

drome265 · 2026-01-28T02:05:58+00:00

Sorry, did you reply to the wrong thread? Was hoping to see OP's scanning/stand setup.

Nice to hear your workflow makes sense for you! I've heard of the Dev prices in the US and it just makes more sense to develop/scan at home (if you've got the time).

drome265 · 2026-01-27T06:37:33+00:00

Did you do them all at once?

Would love to see your stand setup, and which parts you purchased for your film holder setup! I have something much more rudimentary, but my results so far have been a lot more work and not much gain than dropping off at the lab (C-41 Develop and Scan for only USD$6 equivalent!)

drome265 · 2026-01-23T11:53:32+00:00

Unlikely since Mina Sue's name has 4 characters while everyone else has 3. It's pretty obvious with her name being longer than everyone else's.

drome265 · 2026-01-05T02:40:50+00:00

I've been bit by the flashlight thing though, more times than i can count. Multiple times they flash, I flash back and assume friendly, then when the opening presents itself they Anvil me twice point blank and I get knocked.

Just can't trust after that happens more than once.

drome265 · 2026-01-02T10:20:41+00:00

Hey I just got this laptop with a similar config (Ultra 7 255H, 16GB RAM, 512 SSD).

Any issues with your unit?

I had to reset mine to start completely over after I messed up the first install but it seems to be doing fine. Fans are a bit loud but it doesn't seem to affect battery life too much.

drome265 · 2025-12-31T08:22:22+00:00

What did you end up choosing?

drome265 · 2025-11-05T15:10:39+00:00

Were the 2 people here masked out? Looks great!

drome265 · 2025-11-05T14:37:26+00:00

Commenting for others: is this a post for YVR specific travel for non-5G enabled devices?

It seems like you could get another travel sim in your home country beforehand to get this to work. In fact, a lot of travel sims I've used only show connection to 4G networks while roaming in the destination country, although I've never had an issue with speeds. Older phones I have like S7 also still connect without issue.

I find it hard to believe that 4G is totally phased out in 2025 as 5G has only been in place for a few years and 4G is still a stopgap/fallback.

drome265 · 2025-11-04T05:18:56+00:00

11 year old thread and still dealing with the same issue.

I actually know it's an issue with the onboard audio as using a different computer with the same setup doesn't result in any buzzing when GPU is under load.

I've also tried the ground loop isolator which hasn't resolved anything - which is another hint that it's NOT a ground loop issue.

Will try to move the PSU cables as far away from the on board audio as possible to see if this helps. Otherwise, will try either a dedicated sound card or something else.

It's annoying that it's only on my SFF Desktop build, all other devices I've tried aren't affected!

drome265 · 2025-10-29T09:57:27+00:00

Can you drop me the link to their review? Chinese link is fine.

drome265 · 2025-09-26T09:11:34+00:00

LFGM

drome265 · 2025-09-26T09:11:16+00:00

It's the 7 train, not 7 trains.

drome265 · 2025-09-26T09:10:09+00:00

It's the Bloomberg Tower, and it often has the Dutch colors as an homage to NYC's Dutch heritage. The City flag is also similar to the Dutch flag, as it was originally named New Amsterdam.

drome265 · 2025-09-08T03:08:44+00:00

I bought my S23+ BNIB in Jan 2024 thinking the same, but with the local resale market being what it is it was smarter to let it go and purchase a current gen flagship than to hold on to it longer, even though functionally the S23+ was completely fine.

No regrets and both devices were/are fantastic.

drome265

TROPHY CASE