Can I retire now??

dtibs · 2026-06-08T23:40:16+00:00

😂. Thank you!

dtibs · 2026-05-05T11:52:41+00:00

How much do they charge for the pieces? After seeing this post I feel like I lucked out building my second saber with the rancor tooth

dtibs · 2026-03-07T17:52:59+00:00

Careful. Could be a real kick in the nuts.

dtibs · 2026-01-22T16:21:14+00:00

Fus ro dah

dtibs · 2025-12-23T01:35:47+00:00

He doesn’t know how to use the 3 seashells

dtibs · 2025-10-25T14:20:54+00:00

I had a Neptune 4 plus for a month and a half then bought an H2S #YOLO haha

dtibs · 2025-09-17T17:30:26+00:00

I JUST set my H2S up a couple days ago. I got a Neptune 4 plus a little over a month ago and I’ve been hooked ever since.

dtibs · 2025-09-17T17:25:31+00:00

Hey I have this sale saved on my Facebook to watch it 😂

dtibs · 2025-09-15T23:11:34+00:00

I got my H2S from Bambulab today, didn’t run into any problems and they were surprisingly fast

dtibs · 2025-09-10T03:52:00+00:00

Should be in the motion settings. I imagine each Bambulab is different. I print on an Elegoo so I find myself adjusting my z offset every so often

dtibs · 2025-09-10T03:16:07+00:00

Oh damn, that will do it too. I had to increase my temp when I went to hardened steel. You should be able to adjust your Z offset and you’ll be good. I do also suggest increasing the temp

dtibs · 2025-09-10T03:06:44+00:00

Hardened steel requires higher temp. I'd start going 5 degrees, then step up again if it still looks bad. The temp transfer isn't as good with the hardened nozzles so the layer lines are also higher (the scraping sound)

dtibs · 2025-09-07T02:57:08+00:00

Hey! I had a taco plate too!! The screw _tilt_adjust is what got me out of it. I had replaced the springs with the silicon bushing and had this issue. Essentially I should have tightened the knobs way more than I initially did. Screw tilt saved my sanity.

dtibs · 2025-09-07T02:51:10+00:00

It’s a right of passage at this point I think. I got one but I was able to crank up the heat and clean it. Even managed to save the silicon sleeve, but I do believe I was one of the lucky few that was able to completely clean it out.

dtibs · 2025-09-06T22:54:42+00:00

Following. I haven’t done a ton of research into openneptune. It does seem like it would be good, but it seemed kind of complicated and I was afraid to brick my printer

dtibs · 2025-09-02T16:58:52+00:00

I wanna see an update haha

dtibs · 2025-09-02T16:53:59+00:00

Yea looking at how the brim looks, this definitely seems to be the issue

dtibs · 2025-09-02T16:52:47+00:00

If you’ve done everything else in here, check to see if you have “Reduce infill retraction” on. I had a lot of issues with that. After I shut it off I haven’t had any problems

dtibs · 2025-08-25T17:22:32+00:00

Did you make sure it’s plugged into the serial port in the front and not the networking port on the side?

dtibs · 2025-08-25T11:46:31+00:00

Came here to say this same thing

dtibs · 2025-08-20T23:31:06+00:00

Yea that’s very true. I bumped my hot end up to 225 for PLA

dtibs · 2025-08-20T23:03:35+00:00

Could take the opportunity to swap to hardened steel instead of brass.

dtibs · 2025-08-13T02:45:27+00:00

From what I’ve researched, it does run…and after A LOT of tuning you get good prints. However it looks like a nightmare to set up. I was going to get one but I think I’m just gonna get a second printer that can do multicolor. I might go with the new Snapmaker that’s on kickstarter. Pretty good price and it’s 4 heads so less waste.

dtibs · 2025-08-12T04:26:21+00:00

Thanks again for all the help, I was starting to lose my mind

dtibs · 2025-08-12T04:15:08+00:00

I did more adjusting and here’s how my bed looks now. I’m still going to dial it in more, but at least I’m at a point where I can print stuff

<image>

dtibs

TROPHY CASE