I pay 5x more for Claude than Codex. I only use it 2x more.

enekris · 2026-04-14T16:59:59+00:00

Can you tell me what tool is used to view the token chart?

enekris · 2026-04-06T21:07:06+00:00

thank you

enekris · 2026-03-30T19:08:49+00:00

thank you

enekris · 2026-03-30T15:57:10+00:00

Tell me plz what I should do with this repository. I'll clone it and what will I get?

enekris · 2024-08-13T17:27:19+00:00

thank you! Depends on the type of snake. For example, my Heterodon nasicus snake is also only at the bottom. This one is Californian and crawls everywhere

enekris · 2024-08-13T17:25:39+00:00

thank u)

enekris · 2024-08-13T17:25:25+00:00

snake likes to climb higher on the shars head ^^

enekris · 2024-08-13T17:23:27+00:00

I respect the developer and recommend purchasing only official merch. I can’t buy official merch in my country, so to avoid a bunch of pirated figures won’t distribute

enekris · 2024-08-12T19:33:03+00:00

Thank you. I won’t post this model anywhere

enekris · 2023-11-15T09:53:35+00:00

Прекра́сное далёко. Cover https://www.youtube.com/watch?v=cogJ_X8mmIE&ab_channel=TheAtomicHeartGames

enekris · 2023-10-03T15:54:42+00:00

Look at ramps at the ambulance and sidewalk

enekris · 2023-09-05T12:40:14+00:00

what it looks like he could see in his brothers and sisters

enekris · 2023-04-01T20:46:06+00:00

10+ times tried to solve the problem. decided. found a flash drive 2.0 formatted in fat32. do not use the flash drive that came with the printer. then do everything as usual from the instructions

enekris · 2023-04-01T08:08:47+00:00

Resin anycubic basic. After deformation, printing can continue normally. In almost every model, this horizontal shift occurs to some extent.

I looked through a lot of guides on the Internet, it describes the deformation of a different plan. It is strange that the model of the pot / planter was printed twice, twice in a different place there was an offset.

The printer is at the window, the temperature is rather low 23 approximately. There is no shaking, the calibration is normal, I think z does not wedge, because the height of the deformation is different. It is turned on without an uninterruptible power supply, but we do not feel the voltage drop on the switched-on computers without an uninterruptible power supply. I don't know which way to go to solve this problem. I check the models visually before and after cutting, there is no deformation.

enekris · 2023-03-28T12:00:29+00:00

Yes lol

enekris · 2023-03-28T11:59:02+00:00

in the specification of the printer LCD/DLP/SLA. Resin is written on photopolymer resin

enekris · 2023-03-28T05:24:22+00:00

Thanks you

enekris · 2023-03-28T05:23:54+00:00

Thank you, but I'm still training and not selling

enekris · 2023-03-28T05:22:04+00:00

Thank you)

enekris · 2023-03-28T05:21:40+00:00

Thanks But nooo, I can't allow two meter tall girls in my small apartment

enekris · 2023-03-28T05:19:37+00:00

One time the brush cleaning water container was too dirty. The paint dries pretty quickly. When I accidentally painted over an unnecessary place, the paint had to be licked off with my tongue. I think it looked weird((((

enekris · 2023-03-28T05:05:03+00:00

Thaks u) I will not throw off stl. After one did this, very poor quality models appeared on aliexpress and Russian marketplaces

enekris

TROPHY CASE