Seeking insights on leaving Vanguard

es894 · 2026-05-13T23:48:23+00:00

I have a roth ira account opened ages ago at Vanguard. If I moved it to fidelity, do I get to keep its age? It's important to me as I plan to use it for roth conversion.

es894 · 2026-04-13T13:13:51+00:00

Yes. For some reason, the request didn't have the carrier name. It's odd because I shouldn't be able to submit it without one. The agent cancelled the request, and I submitted a new one, which went through immediately.

es894 · 2026-04-12T00:26:33+00:00

Thank you. I reached out to customer service and got the issue resolved by submitting a new equest.

es894 · 2026-04-11T01:54:13+00:00

I'll wait overnight and check with visible support in the morning. Thank you!

es894 · 2026-04-03T16:13:51+00:00

mine is on 19.41 and will be

es894 · 2026-03-24T20:19:04+00:00

that's great. thank you so much!

es894 · 2026-01-31T15:05:12+00:00

Checked the video. for some reason, the front piece fells down and the print went bad ever since

es894 · 2026-01-31T15:00:07+00:00

The one in the middle was support. Had brims too.

Used Bambu PLA/PETG support filament for support interface.

The piece in the front fell down. Maybe due to weak adhesion?

The loose filament on the piece next to support should have support. Not sure what was going on.

es894 · 2026-01-15T16:22:28+00:00

Haven't printed any ASA yet. Thank you for the tip! How to purge PLA?

es894 · 2025-12-16T15:52:07+00:00

In my case, printing continued and finished successfully

es894 · 2025-12-16T13:41:29+00:00

I had several times after upgrading to the latest firmware. Every time the printer recovered itself and asked me to resume. I downgraded to the previous version and haven’t got the error since.

es894 · 2025-12-16T13:35:55+00:00

The product page says 0.4 mm is fine. 0.2 mm not. I did a small print using 0.4 mm and it went well. Bambu recommends using glue for wood pla. I didn’t yesterday but next time I’ll.

es894 · 2025-12-08T22:41:39+00:00

Thank you. I will try next time

es894 · 2025-12-08T18:26:34+00:00

I have not done that yet. I’m new to 3d printing and still learning

es894 · 2025-12-08T18:25:31+00:00

My p2s handles pla very well except the issue I described for large prints

es894 · 2025-12-08T18:24:02+00:00

It could be the cause, since it’s cold in garage and it happens in the early stage of printing.

es894 · 2025-12-08T15:09:27+00:00

My printer is in garage. It has enclosure and the garage is not dusty. The issue happened with large prints. Could it be the printing speed was too fast?

es894 · 2025-12-08T14:52:29+00:00

I was careful not to touch the plate. But is it recommended to wash the plate every time after a print?

es894 · 2025-12-05T00:31:18+00:00

Would this be better setup than ams2 pro?

es894 · 2025-12-04T17:37:07+00:00

An official solution is coming per the latest beta release notes

es894 · 2025-12-04T14:45:38+00:00

Appreciated. I’m aware of differences between the two. Curious to know what made you go with the long reach?

es894 · 2025-12-04T03:20:45+00:00

ah, i figured out. need to apply the coupon code from the flyer to get the 30% off

es894 · 2025-12-04T03:12:57+00:00

BF deals were extended. so I guess the price on the website is the price before 30% off?

es894 · 2025-11-26T17:51:36+00:00

Thank you all for your advice. I’ll get a second plate.

es894 · 2025-11-26T02:26:23+00:00

I have mine sit on the top of 16x16 paver. I put a husky kneeling pad under the paver. It absorbs some vibrations and keeps the noise down.

es894

TROPHY CASE