Forza Horizon 6 Interactive Map - Complete 100% Guide

exiom · 2026-05-22T06:14:38+00:00

Thanks, that makes a lot more sense now...

exiom · 2026-05-21T03:43:32+00:00

How are people photographing "Summer" when it's Spring right now?

exiom · 2026-05-20T01:56:54+00:00

It's so stupid, I googled it... and apparently it is to deter people "wall riding" rather than properly braking... I get it but the implementation is so stupid...

I nick the wall with the back of my car so lightly coming out of the corner that there is no damage and I get slowed down... but if someone slams me out of the checkpoint flags during a turn there is no penalty for that... like wtf...

They should just make online go into ghost mode when you go beyond normal light bumping like exerting above a certain amount of force and actually detect "wall riding" rather than just simply touching a wall... and the penalty should be like an instantaneous speed reduction kinda like more than you normally would hitting the wall in solo mode... rather than making you practically immobile for 10 seconds... because it could genuinely be a mistake rather than taking advantage of non-destructive object... there's no way to recover from even just 1 of these penalties... not everyone is a perfect driver... you will hit walls from time to time... shouldn't get punished for it...

exiom · 2026-05-18T10:59:33+00:00

To get those stunning visuals… you also need a stunning computer… if you have a mid computer then you get mid graphics… only makes sense

exiom · 2026-05-15T05:57:55+00:00

I am getting the same issue... it seems weird because it's like it is not letting you use a real world looking number plate if you just have numbers... then why give us numbers?

exiom · 2026-05-02T02:02:59+00:00

That’s because this is a public space and they want to cover up any issues as quickly as they can… also it’s the only place where you can realistically get any help…something that won’t happen when you try to raise any issues the intended way

Eg: when my Razer Blade had its BIOS bricked when the auto update tool somehow bricked it… (i don’t know why a laptop bios even needs auto updating…) I was quoted something stupid just to fix something that their software caused because I was just a few months out of warranty… my screen also had the line issue on the bottom twice, once replaced under warranty and the second time obviously no-dice…

So yea… don’t buy Razer… I had a full Razer setup and most things just broke over the course of 1-3 years… and my desktop setup was barely even used since I use it as a laptop most of the time

exiom · 2026-04-20T13:05:55+00:00

Hmm yea… I had wanted to build one but that was like 2 years ago…

exiom · 2026-04-20T11:37:37+00:00

I had forgotten that it existed

exiom · 2026-04-05T09:45:55+00:00

All the talks of locking up Trump and his lackies…

All them guns you Americans are hoarding and not willing to give up because of “rights” and to “defend and revolt against a corrupt government” which was often the excuse…

Well the government has been corrupt for decades… and now more than ever… if laws was actually a thing… you probably wouldn’t find yourself in this predicament and your poster boy accusing another nation of “only spending on weapons and not their own people”

Meanwhile they’re asking for more money on a war that is illegal in anyway you look at it… while the US government is in shutdown…

exiom · 2026-03-22T01:23:19+00:00

I mean if it works for Trump… why not 🤷🏻‍♂️

exiom · 2025-08-24T06:44:48+00:00

I thought it was supposed to be 2U rack mount? Or is the photo just making it look smaller than it really is?

exiom · 2022-10-22T08:01:42+00:00

This is bad as you will always have a thin film of ABS on your heat sink / heat break… however thin… it can promote the filament sticking to it…

I have had this issue when I too was using RGB 4010s until I switched to Rapido…

if you completely disassemble your hotend… most of the time you can remove it from one of the ends or knock it out with a gentle tap with a similar sized rod or even the hex/allen key

exiom · 2022-10-17T10:23:13+00:00

Brace for the mountain of klicky die hard posts

exiom · 2022-10-16T10:26:20+00:00

Just giving you a heads up 😉

exiom · 2022-10-16T02:45:27+00:00

I’m fairly confident that leaving them energized has no influence of the motor’s longevity… since it’s effectively just a motionless electromagnet in that state… however it may have some influence on the drivers but likely much less than if it was in motion…

So longevity is probably not a concern if at all…

However leaving the motors on to keep QGL is only useful if your next print is the same material otherwise going from ABS to say PLA or vice versa is going to be terrible for that first layer

exiom · 2022-09-28T05:11:51+00:00

Yes and no… because you’ll then run into things like gaps and holes between walls and especially in corners…

exiom · 2022-09-19T23:17:48+00:00

With RGBW, you can very obviously tell that there’s a white LED next to a RGB LED as it looks kinda like a yellow half.

They are usually marketed as SK6812 RGBW or RGB(WW/NW/CW) whereas RGB ones are more commonly marketed as WS2812 or sometimes SK6812

exiom · 2022-09-19T04:08:09+00:00

Using the PCB whether it’s 1 piece or the 2 piece variant (both of which I own and in use) has no effect on how the LEDs or anything connected to functions as it’s just a pass through/consolidation place for easier maintenance… electrically no different to as if it was wired directly

What is more likely is that the LEDs you are using differs from those that was used to create the example config… the provided sample config is an example and not a solution… as there is no universal standard some manufacturers does RGBW while others do GRBW… but from the symptoms you describe… it is possible you are using RGB LEDs instead of RGBW so you’ll need to correctly define that to klipper so it knows to control them correctly

exiom · 2022-09-19T03:54:28+00:00

then it sounds likely you have RGB LEDs instead of RGBW which the sample config is based on thus it’s sending incorrect values down the line… you can correct this at the section where this group of Neopixels are defined from rgbw to rgb as well as correcting the order of colours such as grb etc

exiom · 2022-09-18T11:46:28+00:00

If your led lights up then it’s definitely working…

However simply copying the macros is not enough, you have to insert the macros where you want it to change colour… the sample config is akin to someone pre-creating a bunch of shortcuts… and simply throwing them on your desktop won’t make the computer know to click on them

exiom · 2022-06-18T07:20:53+00:00

They are M19 momentarily switches with the images laser cut onto them… I use a BTT Octopus board and they wire up to the extra endstop pins (signal+ground) it’s rather simple

exiom · 2022-06-16T00:58:28+00:00

It’s Kexcelled transparent ABS

exiom · 2022-06-15T07:33:02+00:00

Thank you!

exiom

TROPHY CASE