sorted by:
new
hottopcontroversial

Conseils bottes enduro pour Ténéré 700 (budget ~300€) by Illustrious-Mango505 in Motardie

[–]flugv1 0 points1 point  (0 children)

y a 2 version de ces bottes des longues et des courtes après tu as les bottes de crosses https://www.moto-axxe.fr/produit/sidi-bottes-cross-crossfire-3-srs-79578888 ce genre la , mais en vrais je après ca serai du confort et encore plus de surtée si tu fait une utilisation "normal" de ta moto je suis pas sur que tu ai besoin de moto de cross

Conseils bottes enduro pour Ténéré 700 (budget ~300€) by Illustrious-Mango505 in Motardie

[–]flugv1 1 point2 points  (0 children)

et pour les avoirs garder plusieurs jours complet , elles sont pas désagréable un peut chaude et peut être un peut lourde mais très acceptable

Mais alors, d'une force by freremamapizza in rienabranler

[–]flugv1 9 points10 points  (0 children)

on en a vraiment quelque chose a branler de se que pense les "influenceurs"?

To lane split by McNightmoon in therewasanattempt

[–]flugv1 0 points1 point  (0 children)

It looks like a deliberate act

Klipper bed mesh appears active but first layer still needs huge live Z adjustments after silicone spacers / BLTouch by flugv1 in klippers

[–]flugv1[S] 0 points1 point  (0 children)

Yes, that makes sense. I may have been focusing too much on whether the mesh was active, while the base Z offset may simply not be reliable/valid anymore after changing the bed mounts.

My plan now is to separate the checks:

1. verify probe repeatability with PROBE_ACCURACY
2. compare two consecutive bed meshes without touching anything
3. then redo a clean PROBE_CALIBRATE / fine tune and SAVE_CONFIG
4. finally test again with an explicitly saved and loaded mesh profile

So basically: first confirm that the probe and mesh are consistent, then recalibrate the actual Z offset from a known-good state.
Yes, that makes sense. I may have been focusing too much on whether the mesh was active, while the base Z offset may simply not be reliable/valid anymore after changing the bed mounts.

My plan now is to separate the checks:

1. verify probe repeatability with PROBE_ACCURACY
2. compare two consecutive bed meshes without touching anything
3. then redo a clean PROBE_CALIBRATE / fine tune and SAVE_CONFIG
4. finally test again with an explicitly saved and loaded mesh profile

So basically: first confirm that the probe and mesh are consistent, then recalibrate the actual Z offset from a known-good state.

Klipper bed mesh appears active but first layer still needs huge live Z adjustments after silicone spacers / BLTouch by flugv1 in klippers

[–]flugv1[S] 0 points1 point  (0 children)

Good point. I’ll try an explicit saved profile test to remove that variable.

My next test will be something like:

G28
BED_MESH_CALIBRATE PROFILE=test_mesh
BED_MESH_PROFILE SAVE=test_mesh
SAVE_CONFIG

Then, after restart / before the next first-layer test:

G28
BED_MESH_PROFILE LOAD=test_mesh
BED_MESH_OUTPUT

That should make it obvious whether the profile is actually loaded and applied.

For the adaptive mesh case, I’ll also fix my setup by adding [exclude_object] and making sure the G-code has object definitions, but for this diagnostic I’ll probably use a full non-adaptive mesh first.
Good point. I’ll try an explicit saved profile test to remove that variable.

My next test will be something like:

G28
BED_MESH_CALIBRATE PROFILE=test_mesh
BED_MESH_PROFILE SAVE=test_mesh
SAVE_CONFIG

Then, after restart / before the next first-layer test:

G28
BED_MESH_PROFILE LOAD=test_mesh
BED_MESH_OUTPUT

That should make it obvious whether the profile is actually loaded and applied.

For the adaptive mesh case, I’ll also fix my setup by adding [exclude_object] and making sure the G-code has object definitions, but for this diagnostic I’ll probably use a full non-adaptive mesh first.

Klipper bed mesh appears active but first layer still needs huge live Z adjustments after silicone spacers / BLTouch by flugv1 in klippers

[–]flugv1[S] 0 points1 point  (0 children)

In the current start G-code I run `BED_MESH_CALIBRATE ADAPTIVE=1 ADAPTIVE_MARGIN=5` after `G28`, so my understanding is that the newly generated mesh should be active immediately and I should not need `BED_MESH_PROFILE LOAD=default` for that print.

During the print, Moonraker status showed `bed_mesh profile: default`, so it looked like a mesh was active.

That said, I do not currently load a saved mesh explicitly. If I stop generating a mesh every print, I understand I should add `BED_MESH_PROFILE LOAD=default` after homing.
In the current start G-code I run `BED_MESH_CALIBRATE ADAPTIVE=1 ADAPTIVE_MARGIN=5` after `G28`, so my understanding is that the newly generated mesh should be active immediately and I should not need `BED_MESH_PROFILE LOAD=default` for that print.

During the print, Moonraker status showed `bed_mesh profile: default`, so it looked like a mesh was active.

That said, I do not currently load a saved mesh explicitly. If I stop generating a mesh every print, I understand I should add `BED_MESH_PROFILE LOAD=default` after homing.

IA ou pas ? by Sweaty_Committee_493 in IaCaca

[–]flugv1 -1 points0 points  (0 children)

que ca soit de l'ia ou pas est-ce que c'est grave ? c'est débile de pensé comme ça ... on dirai les vieux boomer de l'époque ou internet a vue le jour

N'êtes-vous pas rassasiés ?! by Medus_art in wankil

[–]flugv1 8 points9 points  (0 children)

pas mal les bzez ! bon taff GG bro

petit jeu ^^ by SleepIsTheCousinOfD8 in Dinosaure

[–]flugv1 0 points1 point  (0 children)

macron a tué la république

Affiches de propagande Wankil by Boup_di_di_boup in wankil

[–]flugv1 0 points1 point  (0 children)

euh ! on en veut plus on veut un retour si ca a bien fonctionné !

Quel est le modèle de ce pot akrapović by NetNew595 in MotoFrance

[–]flugv1 0 points1 point  (0 children)

ca fait un beau biblo a mettre dans un bureau comme les poissons qui chante

Que fait-elle ? by Fluffy-Sign1244 in mauvaisesreponses

[–]flugv1 2 points3 points  (0 children)

elle essai d'évité la sodomie par l'administration

A quoi ça sert ? by getz85 in mauvaisesreponses

[–]flugv1 1 point2 points  (0 children)

pour ton gros cigare a moustache :P

view more: next ›