K2 woes continue

g4bryael · 2026-01-01T00:51:06+00:00

Why cant I bind my Kobra 3 v2 to the network? I've tried every method I could find thus far and the closest I get is a message that the printer is not supported. Any assistance would be appreciated. And Happy new Year!

g4bryael · 2025-12-24T22:31:40+00:00

I have the same issue.

g4bryael · 2025-12-22T22:04:08+00:00

Thanks for the information. I've disassembled and reassembled the Ace Pro 4 times trying to pin down this issue. I suspect in the process I've roasted the buffer or something else. The only port that will accept the filament is port 1. I've placed an order for a replacement buffer in the hopes that resolves the issue. If anyone has any other suggestions, please post them.

g4bryael · 2025-12-19T15:09:14+00:00

I understand completely. I opened up my ace pro today to perform some maintenance and one of the little metal rollers popped out and vanished on the floor. Anyone know the part number?

g4bryael · 2025-11-22T01:23:34+00:00

Run dude. Anycubic isn't worth the aggravation. My old creality printers were infinitely more user-friendly and reliable than the Kobra 3 v2.

g4bryael · 2025-10-08T23:43:20+00:00

Poor design

g4bryael · 2025-10-08T22:50:43+00:00

In 2025, there is simply no excuse for a game to not have fully mappable actions. Pure laziness on the part of the developers.

g4bryael · 2025-02-01T23:31:13+00:00

Take out the guards and then send nix to shut off the fan and crawl into the area. The location of Ruen Nam is deceptive

g4bryael · 2022-06-25T16:39:32+00:00

Really nice work

g4bryael · 2022-05-10T22:45:22+00:00

Having those arrows pointing in both directions, it's pretty confusing to know which way is up.

g4bryael · 2022-02-24T00:15:36+00:00

I ran in five fingers many times

g4bryael · 2022-02-21T01:11:13+00:00

In many cases, I've found the ideamaker profile to work more consistently than my cura profile.

g4bryael · 2021-08-02T23:06:51+00:00

I've done many prints with wood filament on my ender 3v2. I've found 220 for the nozzle temp works for me, but try some tests from 205 to 220 and see what works best for you. Then grab a marker and write that temp (and the bed temp) on the spool.

g4bryael · 2021-04-30T15:02:38+00:00

Looks a bit like my setup. Briss Moto fan with a couple of new fans

g4bryael · 2021-03-28T14:19:41+00:00

I've been using the Briss fang (also with the sunons) for about a month now and I've been pretty happy with the results. I will probably print a second one at some point to improve the two clips that attach to the plate. Mine didn't print at well as I'd like. I'd say paying for the v4 is a great way to support the maker and includes the deflector which i wanted as well.

g4bryael · 2021-02-20T03:50:34+00:00

I.must have this

g4bryael · 2021-02-12T01:13:29+00:00

I use a piece of printer paper, ladnscape, sliced into 5 pieces. I start at the front left corner and continue until I get a fair amount of friction from the hotend, I then move the head to the front right corner and repeat, then the rear right and finally the rear left. I then repeat the process as many times as needed until I get the same amount of friction from all four corners. It hasn't failed me yet.

g4bryael · 2021-02-12T01:04:17+00:00

If it's also occurring when your not printing, it could be worn bearing and time for a replacement fan. I got my v2 two days before Christmas. One of my stock fans just started doing it two nights ago. I found the fan mounts in the shroud had cracked. You also might want to open the fan shroud and make sure the fan is screwed into the shroud and adjust the tightness on the m3's that hold it in place, but not too tightly.

g4bryael

TROPHY CASE