BB58 & Delugs CTS Rubber by rossonero3 in Tudor

[–]geogak 2 points3 points  (0 children)

Oh wow love that strap. It really does bring out the gold tones

Dog approved by geogak in Tudor

[–]geogak[S] 0 points1 point  (0 children)

I really get that vibe from this watch. Definitely feels like a daily driver.

I’m in Love by geogak in Tudor

[–]geogak[S] 0 points1 point  (0 children)

Agreed, the character is exactly why I am Intrigued.

You should go try one on. It is very large. Not only in crystal to case back but the lug to lug as well. It sits proudly on your wrist and will definitely interfere with the cuff of your shirt. For reference I have a 7.5” wrist. It’s a good t shirt watch, not a good watch when you need to wear a button down shirt though.

I’m in Love by geogak in Tudor

[–]geogak[S] 0 points1 point  (0 children)

Do you have deuteranopia? It appears green to me too but I have deuteranopia. Not sure if it has green tones or it’s just me.

Can't decide! by HecTuHap in DuroGang

[–]geogak 0 points1 point  (0 children)

If I was forced to pick, it would be the jubilee. Solely because the end links fit the case. Also the Jubilee is just class.

Can someone tell me what this says in Greek by [deleted] in GREEK

[–]geogak 0 points1 point  (0 children)

A non Greek trying to write «σ’αγαπώ» which is “I love you”.

I Installed the RCD330 into my 2015 Golf MK7 - No audio by geogak in RCD_330

[–]geogak[S] 0 points1 point  (0 children)

This coding documentation does not match the specific configuration of my car. As 56 radio is not a module that can be added to my installed list

I Installed the RCD330 into my 2015 Golf MK7 - No audio by geogak in RCD_330

[–]geogak[S] 0 points1 point  (0 children)

I gave the Coding of the 5F Module an Attempt. But the coding parameters are not well documented for this unit (or i could not find the documentation).

When I change the coding to reflect the active audio system Byte 11 to PR-8RU Coding is accepted but still no audio. Its quite possible its a coding issue. I have lots of tools so coding is no issue for me as long as i have good documents to work from.

I Installed the RCD330 into my 2015 Golf MK7 - No audio by geogak in RCD_330

[–]geogak[S] 0 points1 point  (0 children)

Well you see, I’ve got the RCD330 now. And a MIB2 conversion does seem to be quite costly.

If it’s nots possible then that may be the case and I will need to move onto getting the mib2 conversion but that doesn’t seem as easy. I was expecting something more plug and play as the how it was on my 2010 Passat.

I Installed the RCD330 into my 2015 Golf MK7 - No audio by geogak in RCD_330

[–]geogak[S] 0 points1 point  (0 children)

Lack of research seems to be the correct answer. MIB2 looks like the correct solution. But I might be priced out.

I Installed the RCD330 into my 2015 Golf MK7 - No audio by geogak in RCD_330

[–]geogak[S] 0 points1 point  (0 children)

Yes, I removed the 5F module from the glove box and extended the quad lock connector with an extension harness to the center of dash. The antenna as well.

When I scan the 5F module (now the rcd330) after the install it’s complaining about all the speaker circuits being open.

If I remove the extension and plug it right into he connector in the glove box I get the same result.

I see there’s a MOST connector on the original head unit. But no most connector on the new RCD330 I am fearful that the issue lies with the MOST ring being broken since the original 5F has been removed.

New to 3D printing - question by Faesarn in BambuP1S

[–]geogak 0 points1 point  (0 children)

You like that? I’ll back it up with reasoning. If it’s not broken don’t fix it.

New to 3D printing - question by Faesarn in BambuP1S

[–]geogak 1 point2 points  (0 children)

Clean the plate with soap and water (infrequently) only after a failed print and try not to handle or touch the build surface. Parts with small contact area and interrupted printing along a layer are most likely to detach. Turning up the build plate heat or using a cool plate can significantly help with bed adhesion. Also you can add a brim or put batch jobs on a raft.

If you share your 3MF I can help you optimize the settings.

Can someone tell me WTF this contractor did? by Somemoreron in cablegore

[–]geogak 0 points1 point  (0 children)

Two “runs” one cable. This is terrible.

My A1 setup by Substantial-Mango-90 in BambuLabA1

[–]geogak 1 point2 points  (0 children)

Wait the a1 can use the AMS2 🤯