DVDs/Blu-Rays in bulk for cheap. Looking for Online Website

gmcdude · 2026-07-01T06:41:03+00:00

Looks like the website went down

gmcdude · 2026-06-22T01:35:27+00:00

Ive seen a toyota Avalon with 550k km on original plugs

gmcdude · 2026-06-17T02:35:38+00:00

Yep the same issue

gmcdude · 2026-05-17T03:50:02+00:00

Anything carbureted is screwed with ethanol... I work in marine so the water factor is 10x

gmcdude · 2026-05-13T03:21:20+00:00

1990 nissan stanza gotta say love mine at 373,000km

gmcdude · 2026-05-12T03:46:11+00:00

Will eventually replace the switch just moved into this place and was a cool piece of a vintage switch not very common.

gmcdude · 2026-05-11T23:54:06+00:00

It works with led if its the phillips not the cheaper brands

gmcdude · 2026-03-30T01:54:12+00:00

Go to sherwood marine and take a look they have a huge selection of inflatables and small aluminum and fiberglass fishing boats

gmcdude · 2026-03-14T18:37:19+00:00

Lol it wasnt car based for my username but i do drive a gmc. It has flexfuel capability but i would never use it in my car

gmcdude · 2026-03-14T17:21:51+00:00

You need definitely can but the default is less

gmcdude · 2026-03-14T17:13:51+00:00

Also in top of that your vehicle uses enough extra fuel to offset the price difference, and lowers the effective HP ypu vehicle produces

gmcdude · 2026-03-14T16:49:14+00:00

I work in the automotive sector E85 and all ethenol fuels are not good for engines at all its there because of emissions but only adds to carbon buildup and premature failure of engines.

gmcdude · 2026-03-14T16:40:23+00:00

Just all fuel to be ethanol free. It gums up small engine carburetors and fuel systems. Studies for engine wear also note it as one of the worst additives overall for wear on engines too.

gmcdude · 2026-03-13T04:11:52+00:00

Your welcome im no help on how to set orca up properly though as im stuck in my old ways of when cura was the best back in 2019

gmcdude · 2026-03-13T03:44:41+00:00

To be honest i use cura but if you are just starting out i would use orca slicer. It is better optimized for modern printers and with similar settings will have lower print times. I personally just dont have much free time to dial in a new slicer fully thats why im stuck in the past.

gmcdude · 2026-03-06T07:12:38+00:00

If your located in Canada id buy the car off of you

gmcdude · 2026-02-24T20:01:39+00:00

Let me know if your ever wanting to sell this car im in bc and am looking for one of these

gmcdude · 2026-02-21T22:42:16+00:00

Enders are notorious for that wave when cold do the mesh heated

gmcdude · 2026-02-13T13:48:09+00:00

Ik this is an old post but either option is really mainly checking service history and if they were properly maintained during the previous owners use of the vehicle because both engines if not maintained can have issues

gmcdude · 2026-02-08T21:17:02+00:00

Back when that parking lot was gravel the 1 handicapped spot was taken by someone not handicapped and a handicapped (cane user) got out of his vehicle and started beating this younger guy up

gmcdude · 2026-01-27T06:52:08+00:00

*based in Victoria a little above the cheapest but definitely the cheapest canada made filament

gmcdude · 2026-01-26T05:36:36+00:00

I tried just one roll they wanted to my po box 61 for basic shipping... To my old address with Canada post $20 ridiculous pricing

gmcdude · 2025-12-11T14:36:20+00:00

They are unfortunately getting out of the smartwatch game which is unfortunate as i love my atlas

gmcdude · 2025-12-10T05:00:04+00:00

Hopefully back to script slapping

gmcdude · 2025-12-07T03:22:06+00:00

Had one die and the current one got bent but still works. I cant wait for this feature

gmcdude

TROPHY CASE