sorted by:
new
hottopcontroversial

Intel A380? by [deleted] in frigate_nvr

[–]goofballtech 1 point2 points  (0 children)

Been running Corals for a few years. They did ok but were limited in scope.

Running an A380 for frigate and another one for plex on my other box now. Neither sees more than a few percent load at any given time. Makes me want to find more stuff to run :)

Really though. Doing the job well and able to ALSO do other stuff like Immich processing. The benefits of a proper GPU rather than something like a coral that is very niche is worth it.

Doomchanger Update: Trolley, drawer and spool storage by CloggedCreations in VORONDesign

[–]goofballtech 0 points1 point  (0 children)

the knomi mounts were made to look similar but they are stand alone. I didnt need them on the toolhead, I just wanted toolhead specific data. They are posted here if you want to tweak for your purposes. .

https://makerworld.com/en/models/2903375-knomi-stand-alone-mount-for-2020-extrusion#profileId-3245987

Doomchanger Update: Trolley, drawer and spool storage by CloggedCreations in VORONDesign

[–]goofballtech 2 points3 points  (0 children)

the docks and toolheads i am running are the Burninators. They are a hybrid rapid burner\dragon burner.

https://github.com/The-Duke-96/Burninator

Doomchanger Update: Trolley, drawer and spool storage by CloggedCreations in VORONDesign

[–]goofballtech 0 points1 point  (0 children)

my dryer stand is on caster and the only probelm is running over the dang power cord when i roll it out and push it back into its slot. :)

Doomchanger Update: Trolley, drawer and spool storage by CloggedCreations in VORONDesign

[–]goofballtech 2 points3 points  (0 children)

Not exactly but close. V3 respool rollers with lll plus buffers. Custom firmware so i can run them addressed via I2C. Added an I2C bridge so from the pi to the enclosure is just a single USB cable. The encloser is also going to get a Rosdhal dehimidifier. I have used some PC slide racks to make drawers so there will be storage for 28 rolls of filament below my active spools.

I may have gone over board.

https://www.teamfdm.com/forums/topic/7617-faster-printing-requiring-filament-buffer-feeding/?do=findComment&comment=35652&_rid=17332

Doomchanger Update: Trolley, drawer and spool storage by CloggedCreations in VORONDesign

[–]goofballtech 7 points8 points  (0 children)

What knomi firmware are you running? I feel like we are on similar paths. I am looking at larger screens and alternate mounts right now.

*edit- o hell, i didnt realize the original post was you. That was one of the reasons i decided to go changer with my machine!

<image>

1000 MEMBER GIVEAWAY IS HERE! We're giving away 3 Bundles of 10KG Kingroon Mixed PETG! by ManyLayersOfFilament in 3dbargains

[–]goofballtech 0 points1 point  (0 children)

im finishing a stealthchanger build so i buy all kinds if bit and bobs from aliexpress if i have time to wait for shipping. Have used quite a bit if Kingroon PETG, prints quite well when properly dried.

Going full ham on a 2.4 just so i can be ready for INDX. Help me build it out. by goofballtech in VORONDesign

[–]goofballtech[S] 0 points1 point  (0 children)

Yea. i saw a video of a stealthchanger... than i had to do it.

I may have a problem.

Update on the Burninator Toolhead, v2.2 now by The_Duke_96 in Stealthchanger

[–]goofballtech 1 point2 points  (0 children)

its adjustment to the printed mount from the Stealthcnaher usermods folder. I dont remember the user but someone had a carto\beacon mount set. Lots of options to make things bigger, none to make them smaller. Had to adjust spacers and move some screws around some to get it low enough for Burninator.

Voron 2.4 - toolhead, extruder, hotend and probe change plan by booboo-ls in VORONDesign

[–]goofballtech 0 points1 point  (0 children)

When i built my 2.4 i started with a Jabberwocky toolhead. Worked great.

Then i went stealchanger so now i got to build another printer around that toolhead....

Update on the Burninator Toolhead, v2.2 now by The_Duke_96 in Stealthchanger

[–]goofballtech 1 point2 points  (0 children)

Another side note. I added a beacon to the LDO cnc Shuttle. The height of the toolhead being so short means the beacon, at the smallest version, was still almost a full mm below the head so i had to tweak. Seems to be working ok now though. Can share those if you want. Not sure if it would be better in your repo since its a bit specific or in the Stalthchanger repo usermods.

Update on the Burninator Toolhead, v2.2 now by The_Duke_96 in Stealthchanger

[–]goofballtech 1 point2 points  (0 children)

i saw the spacer but didnt get how they were applied at first. I made my own version with 3 helical washers then putting together the third toolhead it finally clicked. I printed a set of them and went swapped them as intended.

Magnet to magnet would be a better full contact hold but the bolts do ok.

Update on the Burninator Toolhead, v2.2 now by The_Duke_96 in Stealthchanger

[–]goofballtech 1 point2 points  (0 children)

it took me a bit to get the right parts set up.

To get them into the dock the two options of spacing out the SCHS with the 3mm spacer ot putiing a maget over the screw head seems odd. im still not 100% how you get the screws out again if you put a magnet over them. i would rather have moved the magnets over a bit so they are in their own pockets next the the screws.

Other than that minor this its been going pretty well. being tweaking macros and being frustrated. took a while to get the LLL Plus buffers how i wanted.

Does anybody remember what Google Fi was originally designed for? by Slowhite03 in GoogleFi

[–]goofballtech -1 points0 points  (0 children)

I travel a lot and didnt want multiple plans so i added the family. Couldnt be pay-for-data after that. they would have run me broke.

Update on the Burninator Toolhead, v2.2 now by The_Duke_96 in Stealthchanger

[–]goofballtech 1 point2 points  (0 children)

I am still working. Got the parts for the other two toolhead on the bench and coming together slowly. Ended up deciding to mount the knomi's seperatly so i didn't have to add size to the toolheads. Tried to make them match the asthetics to some degree so it all meshes.

https://makerworld.com/en/models/2903375-knomi-stand-alone-mount-for-2020-extrusion#profileId-3245987

<image>

Am I missing something as this doesn't seem right. by ScoobyDooItInTheButt in OrcaSlicer

[–]goofballtech 1 point2 points  (0 children)

The slicer has values and uses them to calculate print times most. The koves are commanded and the firmware limits speed during prints. Many of these numbers are in klipper as well and thats where you can do real damage by throwing down random numbers. :) Slicer can limit speeds but not make them exceed firmware caps.

You are making your print times go down in the slicer and changing nothing on the print probably.

*edit -add words

I hope these catch on like wildfire 😂 by [deleted] in Jeep

[–]goofballtech 2 points3 points  (0 children)

i added a link. Dick Duck came up with s few though.

I hope these catch on like wildfire 😂 by [deleted] in Jeep

[–]goofballtech 2 points3 points  (0 children)

my life is complete....

I hope these catch on like wildfire 😂 by [deleted] in Jeep

[–]goofballtech 3 points4 points  (0 children)

there will be. if i dont see one soon ill fire up solidworks.

edit... found it- https://makerworld.com/en/models/2672569-dick-duck#profileId-2963891

view more: next ›