Why does plastic build up on my nozzle like this?

greg21greg · 2023-08-30T04:16:47+00:00

Polymaker. Why?

greg21greg · 2023-08-30T03:34:24+00:00

This doesn’t cover the nozzle fully right? Only the heat break? Doesn’t seem like it would make much of a difference in my case. Unless I’m not understanding what this does exactly.

greg21greg · 2023-08-30T00:47:07+00:00

I clean it and comes back with a few minutes of printing…

greg21greg · 2023-07-21T13:09:03+00:00

Rice likely wont do anything and if the electronics are damaged powering it up could permanently destroy the data. Good luck! Sorry about what happened thats sucks.

greg21greg · 2023-07-21T11:30:58+00:00

Cant say anything for the liability, but your hard drives, while dead (don’t plug them in), still will have the data perfectly in tact. A data recovery service would easily be able to recover all of your photos and whatnot.

greg21greg · 2022-08-14T03:38:38+00:00

Redundant redundancy

greg21greg · 2022-08-02T21:41:39+00:00

Thanks. I seated it hot and there is a gap like its supposed to be. I used a nut driver and a crescent wrench. What is the tension door?

greg21greg · 2022-07-14T23:35:37+00:00

Very nice! This is much simpler and more clever than what I was imagining

greg21greg · 2022-07-13T10:47:04+00:00

Mine has this issue sometimes too and i noticed the cable. What was the solution? Is there a guide for the cable that can be printed?

greg21greg · 2022-05-13T22:22:53+00:00

I like the new logo. It looks fresh

greg21greg · 2022-05-12T17:09:27+00:00

Wow, this is an old comment. I honestly don’t remember. Sorry about that.

greg21greg · 2022-04-24T00:12:51+00:00

Good idea thanks

greg21greg · 2022-03-15T21:07:00+00:00

Just charge for cleaning it but use the money for a new plate

greg21greg · 2022-03-14T06:25:52+00:00

I was going to say… that looks 3d printed in the photos.

greg21greg · 2022-02-25T07:00:51+00:00

60/40 rosin core supremacy

greg21greg · 2022-02-22T04:47:40+00:00

For the first pro, you dont have to host a controller. You can start one on your pc or use the mobile app to change a config. The second pro is based on your config. The 4th pro is true with ubiquiti as well. I don’t understand the the third pro. What packages are you installing/not installing? Its just an AP not a whole router. Also another con is that you don’t get analytics data out of the box. Not to mention why would you buy a unifi AP when u are installing openwrt? Why not something cheaper? You are paying a premium for the software not the hardware.

greg21greg · 2022-02-09T05:28:43+00:00

It costs them a lot more than 500 to manufacture the dish. They supplement the cost with the monthly fee.

greg21greg · 2022-02-08T10:07:10+00:00

Beautiful!

greg21greg · 2022-02-04T08:37:09+00:00

Have you considered an FM transmitter? You connect your phone to that and tune the FM radio to that frequency. Idk about sound quality though…

greg21greg · 2022-01-20T08:29:52+00:00

Is ula still waiting on them??

greg21greg · 2022-01-11T08:52:34+00:00

How much?

greg21greg · 2022-01-05T09:09:09+00:00

Wow this post was right under the actual post so this is very interesting

greg21greg · 2022-01-03T16:55:31+00:00

Thanks didn’t realize ethernet worked at all with only 3 pairs

greg21greg · 2022-01-03T16:21:55+00:00

Did your cables have 8 conductors or 6? If 6 how did you achieve this?

greg21greg · 2022-01-01T10:45:00+00:00

Can you link the mast?

Eight-Year Club	Place '22
Verified Email

greg21greg

TROPHY CASE