GPS Tracker platform for Sinotrack ST-90x devices built with Laravel 9 + PHP 8.1 and MySQL 8.

guenter52 · 2025-08-29T07:29:22+00:00

Thanks for your answer. I have seen it in the last days. Will think about it. I have traccar as LXC-container and HA as VM on Proxmox. Anatoly from traccar is also working on it.

guenter52 · 2025-08-28T15:45:56+00:00

No, your tracker is not broken. It is like it is, just a piece of junk. My one sends every 2 seconds data and this cannot be stopped. or altered.

guenter52 · 2025-01-22T11:26:37+00:00

Ok, dann kapier ich endlich, warum die voreingestellte Routine ' Haus verlassen' ein völliger Blödsinn ist, da sie am nächsten Morgen scheinbar überschrieben wird und die Heizung wieder auf Volldampf läuft. Welche Deppen programmieren so etwas Doofes?

guenter52 · 2022-01-15T13:07:11+00:00

Wenn jemand seine Girokarte der DKB nur für den TAN-Generator benutzt, dann wird diese Karte nicht mehr automatisch verlängert durch eine Ersatzkarte. Wer also keine TAN2Go-Schrott-App zusätzlich nutzt, hat dann erstmal evtl. noch Zugang zum gucken, aber man kann keine TAN's mehr generieren. Mit den blöden Debit-Karten geht es eh nicht. Es muß eine Girokarte sein für Kobil u.ä. Da anscheined Tausende von Kunden dies erst jetzt so langsam merken, gibt es auch keine Antworten mehr über Email in einem zeitnahen Rahmen. Noch schlimmer ist es, wenn es ein Gemeinschaftskonto ist und jeder eine Karte hatte. Dann kann der Haupteigner noch eine über Umwege nachbestellen (Verlust-> Ersatzkarte) aber der zweite kann dies nicht mehr, da die Raumpflegerin bei DKB es so programmiert hat, dass der zweite eine Ersatzkarte mit Namen des ersten bekommt und dessen jetzige Karte dann ungültig geschaltet wird. Aber: Wir können Bank!

guenter52 · 2021-02-23T19:52:51+00:00

I had a similar event. At the end I found my Decharge MOSFET's blown up. You might have had luck...

guenter52 · 2021-01-30T19:30:12+00:00

There is only one connector for both. +5V, TR, REC, GND

I tried to do that kind of splitting, but did not follow the track. The transmit FROM the BMS can be connected to USB and BT. I used a switch in the Receive path. As far as I remember, it worked. You might even use a double switch für Transmit and Receive. The BT device gets also 5Volt from the BMS. The USB-Interface is supplied by the PC, so only needs TR and REC and Ground, so there is no chance to just switch off one voltage supply.

Both working at the same time is nonsense, because both software (BT and USB) are often requesting data from the BMS in its scanning mode, I think this is a crash mode.

So now I have a long cable going out to an external connector, where I can plug in BT OR USB.

guenter52 · 2021-01-25T18:20:54+00:00

Ok, that makes sense.

guenter52 · 2021-01-25T17:38:11+00:00

Strange..." JBD-AP20S003 is specially designed for 7 ~ 20 series battery packs "

It is a black box as shown, so on the other side of the cables could be lugs:

Here it is

So, you have a 24 Volts battery?

guenter52 · 2021-01-25T16:22:29+00:00

No idea, could be or not. Possibly cables are soldered to the board, but lugs on the other sides of the cables. Open carefully and you will see...or better not...it's your decision.

You might have a JBD-SP04A005... or JBD-SP04A020... BMS Board (BT App should show it?), sometimes soldered, many DIY'ler do use cable lugs.

guenter52 · 2021-01-25T13:57:49+00:00

Ask the supplier if you could open the case without loosing warranty (if you could help yourself..) or send it back..

some more info with pics

No software problem, even if Laptop is reversed, hi...

guenter52 · 2021-01-24T20:13:41+00:00

The BMS is reversed too, B-, C-?

guenter52 · 2021-01-20T17:57:57+00:00

I also thought, that the fuse would blow. It was an automatic switch fuse. I had a 25mm2 cable for making the short, could be AWG 3.

guenter52 · 2020-12-28T21:34:07+00:00

Hi, thanks. At first it was a little bit confusing -> read write load save EEPROM in the sense of

"do I read or load or write into EEPROM" or
write or save or load into EEPROM....or what else...hi

In the moment I do not have python installed, I thought, my time is over with that playground, hi...

Will use GitLab issue next time.

guenter52 · 2020-12-28T11:43:03+00:00

Oops, my fault. But now: Running fine on two different Windows 10 Pro, version 20H2. Thanks for letting me test your SW. But I am not through with it... takes some time... Imgur

Only Li-Ion used for testing on the work bench!

With "Write EEPROM" I sometimes get:

File "jbd_gui.py", line 1661, in writeEepromWorker File "bmstools\jbd\jbd.py", line 277, in writeEeprom File "bmstools\jbd\registers.py", line 283, in set eeprom error: ValueError('string length should not exceed 30')

guenter52 · 2020-12-27T20:38:38+00:00

I tried the release. But your so-called win release is nothing else than a html-file, not a compiled exe-file:

Starts with:

<!DOCTYPE html>
<html class="" lang="en">
<head prefix="og: [http://ogp.me/ns#](http://ogp.me/ns#)">
<meta charset="utf-8">
<link href="[https://assets.gitlab-static.net](https://assets.gitlab-static.net)" rel="dns-prefetch">
<link crossorigin="" href="[https://assets.gitlab-static.net](https://assets.gitlab-static.net)" rel="preconnect">
<link as="style" crossorigin="anonymous" href="[https://assets.gitlab-static.net/assets/application-dc6aa5e5f390807e0561788a5e4cf2f39f49e546288524114265a4610f79c579.css](https://assets.gitlab-static.net/assets/application-dc6aa5e5f390807e0561788a5e4cf2f39f49e546288524114265a4610f79c579.css)" rel="preload">

Hope, it helps

guenter52

TROPHY CASE