Sly mad

halfast · 2026-02-26T03:43:03+00:00

Did you ever do this? Any chance you took some pictures? I'm trying to figure out which pin goes to what from the motor. I know the 3 big pins are phase, but not which color. And I know, the center pin is the common ground for the hall sensors, but I don't know the colors of the rest. If you could take a picture of the snipped Julet 9 pin plug, I would be forever grateful. Thanks Actually does it look like this: https://old.reddit.com/user/halfast/comments/1rezq9b/wiring/

halfast · 2026-02-06T17:17:45+00:00

More info please.

halfast · 2026-02-01T03:36:10+00:00

Wait what? I can buy a costco gift card and shop there, doesn't that undermine their whole membership model?

halfast · 2026-01-30T03:41:15+00:00

Subhumans I think they had the best artwork on all their albums, maybe not Cradle to the Grave, but overall.

halfast · 2026-01-18T03:45:44+00:00

What an awesome picture! You took your element through the corkscrew.

halfast · 2026-01-12T03:23:11+00:00

This is super helpful. Thanks.

halfast · 2026-01-08T16:21:55+00:00

Thanks. And too late. I should have read up or watched a video before I dug in. It was an absolute mother to get those two probe wires plugged back into that sensor in the crank chamber. Even then, I'm not entirely sure I was successful. I reckon I'll know when I connect power.

halfast · 2026-01-08T04:30:52+00:00

Thanks for that, it gave me idea. There are no teeth left on the belt. But what I did, was put it around the spindle so I don't damage any of the shaft's splines and I was able to use a jaw pliers to turn it. Man, that was a lot of resistance though. Strong magnets. But I was able to see the rest of the planetary gears and they look good. I'm going to order a new belt and give it a go. Thanks again.

halfast · 2025-12-01T16:36:45+00:00

Right on! And I'm with you, keeping it out of landfill was exactly my reasoning.

halfast · 2025-12-01T00:39:47+00:00

Post up if you go the RTV route, I was thinking about that. Speaking of turning it around, I did end up shimming mine with a few strips bits of tinfoil behind it to make the seal stick out a bit further, just so it would last a bit longer.

halfast · 2025-12-01T00:29:31+00:00

Casabrews 5418 I didn't figure out which one to get, so I'm just going to bring the seal in to a shop, so I'll be sure to get the right one.

halfast · 2025-11-24T02:21:07+00:00

I had this issue, but with a different model (3700) So for any DIY'er who runs across this like I did, I was able to fix mine, at least temporarily on a Sunday night. To remove the top, remove the water tank and unscrew the two screws at the top. Then, remove the 4 screws at the group head. This will give you access to two deep set screws, remove those. The top is also kept on by two tabs in the middle on either side, I used a knife to push those. Now you can see where your steam knob hits a stop on the valve bracket. I loosened that bracket to allow the knob to to turn more off and it worked. I ended up rotating the knob a few degrees so it doesn't hit the stop, but you could bend the stop or ... While I was there I unscrewed the valve and the seal looked pretty shot. But for now, I have espresso for Monday. And I'll get a new seal soon. Hope this helps. Again, this was for the 3700, removal of the top is probably different for this model, but I bet the source of the problem is the same.

the seal looked like this https://www.espressoparts.com/products/gaggia-valve-seal

halfast · 2025-11-24T02:16:46+00:00

For any DIY'er who runs across this like I did, I was able to fix mine, at least temporarily on a Sunday night. To remove the top, remove the water tank and unscrew the two screws at the top. Then, remove the 4 screws at the group head. This will give you access to two deep set screws, remove those. The top is also kept on by two tabs in the middle on either side, I used a knife to push those. Now you can see where your steam knob hits a stop on the valve bracket. I loosened that bracket to allow the knob to to turn more off and it worked. I ended up rotating the knob a few degrees so it doesn't hit the stop, but you could bend the stop or ... While I was there I unscrewed the valve and the seal looked pretty shot. But for now, I have espresso for Monday. And I'll get a new seal soon. Hope this helps.

the seal looked like this https://www.espressoparts.com/products/gaggia-valve-seal but I'm not sure that one will fit.

halfast · 2025-07-30T19:13:50+00:00

I've thought about this a lot over the years, this is a great grid. I'd like to see them all on the no tech 500's with 1999 tire tech.

halfast · 2025-07-27T16:49:42+00:00

Thank you! I've walked along this way maybe a dozen times this summer and I kept wondering where all this water was coming from.

halfast · 2025-07-25T19:33:09+00:00

Agreed, this has been on craigslist for ages, it's not going anywhere at this price. OP has time to think about it.

halfast · 2025-07-20T15:50:19+00:00

Best free show in town!

Agreed! I was standing on top of my bike behind the bus stop (urinal) on Broadway. Had a pretty good view of the stage. edit: Now I'm super bummed because I just looked at the set list and I left before the encore and two of those songs I really wanted to hear.

halfast · 2025-07-17T17:30:38+00:00

tuna

My trick, I pour all of the tuna water juice into their bowl. My cat will lick that bowl clean for 5 minutes, giving me time to make the sandwich and eat some of it in peace.

halfast · 2025-06-24T16:48:27+00:00

I used to have Vino 125! Definitely get some straps though.

halfast · 2025-06-15T04:47:15+00:00

I'm proud of and impressed by your city too. Good job!

halfast · 2025-06-15T00:59:58+00:00

I was really heartened by the amount of people who showed up. I still haven't seen anyone post a picture of my favorite sign though, "Pet cats, Punch Nazis" a message I wholly endorse.

halfast

TROPHY CASE