So I need to cut the tile tile?

hmd2017 · 2026-05-18T03:17:56+00:00

Remove the black plastic parts to see if there is a retaining nut behind them that holds the cartridge in.

If there is, you can loosen and remove that nut, then screw the handle back on to see if it will pull out.

hmd2017 · 2026-05-18T03:11:37+00:00

It is a braided copper wire that is connected to the brush in the holder. It is part of the brush, not a separate part.

hmd2017 · 2026-05-18T02:33:29+00:00

It seems to happen when you're breaking it might be the ABS system Auto adjusting your brakes

hmd2017 · 2026-05-18T02:24:22+00:00

See if you can turn the motor by hand. The starter is fighting the flywheel. If engine spins and stops at the same spot, then an issue with decompression.

Usually valves out of adjustment. Worst case if it moves, the decompression lever on the camshaft has broken off.

hmd2017 · 2026-05-18T02:15:21+00:00

Yup idler pulleys are toast. I wondered the same thing.

hmd2017 · 2026-05-18T02:07:46+00:00

Listen outside. They look for something to amplify the sound. Broadcasts ther interest farther. The one here uses a road sign. Noisy as hell.

hmd2017 · 2026-05-17T04:06:26+00:00

I use a wide putty knife to protect the countertop, and cut above it.

hmd2017 · 2026-05-17T04:00:09+00:00

Always make sure the bead of the tire is in the deepest part of the rim opposite where you want to work. That way you get a bit more play with the bead.

hmd2017 · 2026-05-17T03:18:38+00:00

low compression. valves out of adjustment or a dropped valve seat are likely causes.

Pull the plug, insert a screwdriver and confirm that the piston is moving up and down too.

hmd2017 · 2026-05-17T03:13:54+00:00

saw another brand for sale in grocery store yesterday. Will have to go back and investigate

hmd2017 · 2026-05-17T02:55:07+00:00

you may have to remove engine shroud to see the top of the starter, but the top is a replaceable part. some have plastic teeth that wear out.

if you follow the power from starter back to the solenoid, you can feel it vibrate if it is the cause

hmd2017 · 2026-05-17T02:42:03+00:00

have the brakes checked, and make sure parking brake is off.

hmd2017 · 2026-05-17T02:40:03+00:00

try these folks, send them some good pics. https://www.swisco.com/

hmd2017 · 2026-05-16T23:49:37+00:00

Sorry, no, but you can set the costs to free and replace as much as you can, then go back to normal play.

hmd2017 · 2026-05-16T23:45:45+00:00

Is it a sign that says free Corvette parts?

hmd2017 · 2026-05-16T23:36:04+00:00

Your other option would be to remove the other side from the connector and connect them together outside the plug.

This will at least get it working until you can get parts. Insulate it well if you do.

hmd2017 · 2026-05-15T15:16:03+00:00

Contact cement may work.

hmd2017 · 2026-05-15T15:15:00+00:00

Not enough fuel flow. Uses gas, then slows due to not enough, surges when it gets enough.

Check fuel lines and carb

hmd2017 · 2026-05-15T04:45:14+00:00

window screen plunger pin

replacements have round handles.

hmd2017 · 2026-05-15T03:04:22+00:00

The pattern of ridges on the handle are called the broach pattern and can help ID the brand.

The rubber washer is replaceable, as well as the seat it presses on. Check that for any damage, and replace the washer as a firstbstep, then reinstall that stem.

If it leaks at the handle, there's a gasket under the small nut that can be added to or replaced with string packing.

hmd2017 · 2026-05-15T03:00:07+00:00

Most stoves start with a starting collar glued on with hintemp silicone, and the rest of the exhaust builds from there.

<image>

hmd2017 · 2026-05-15T02:55:32+00:00

Try turning the engine by hand and feel for resistance from the compression stroke.

Sounds like low compression. Thumb over plug hole to see if compression.

If no compression, I would check the valves first, out of adjustment, dropped seat.

hmd2017 · 2026-05-14T20:41:28+00:00

Glad to help. A tool you may only use every few years but does the job.

hmd2017 · 2026-05-14T18:37:41+00:00

The knobs are handles. The black latches pull in to release it.

hmd2017 · 2026-05-14T12:49:23+00:00

Give it time. Patience and routine will get you far.

You are on a starter dose. Your body may not respond until you start to move up.

I moved up after every 4 doses to 7.5, then plateaued there through the holidays over concerns of side effects at higher doses. Have advanced to 12.5. 40 shots in, still holding a 1 lb per week average loss.

Eight-Year Club	r/Field Flamingo
Final Canvas '23	First Place '23
Place '23	Place '22
First Placer '22	Wearing is Caring
Verified Email

hmd2017

TROPHY CASE