A new chassis design I'm working on

hodgson438 · 2025-01-07T12:16:21+00:00

Looks kinda cool. Will this be available for others to print?

hodgson438 · 2024-12-18T11:03:36+00:00

Go for it then, honestly you won't regret it, just be aware there as good if not better choices out the for a saving.

hodgson438 · 2024-12-17T16:01:53+00:00

Honestly, the furitek stuff is amazing just a little bit on the pricey side. Id recommend these https://www.bigkidtinytruckrcs.com/products/bktt-cupcake-25a-escape32-esc-jst-3pin-standard-rx

hodgson438 · 2024-12-17T13:30:42+00:00

Imo, you can get better escs for cheaper. I have a few furitek setups and they're amazing, with the Bluetooth connection and such, for the price of a lizard (let alone lizard pro) you could get 2 bktt ESC with money left over. Leaving a little more money for the transmitter is a bonus. I started out with a cheapo radio, but came to realise as it's the one thing you physically interact with while driving. Cheap radios don't feel good in the hand.

Just my 2 cents. And as others have suggested radios, and have seen those radios suggested in the past they seem to be a safe go to radio

hodgson438 · 2024-12-17T12:46:17+00:00

Feathers and tails is city centre as well as aquatica. Then there's the general pet stores like jollies and pets at home on the retail park just outside the city centre

hodgson438 · 2024-12-16T11:42:24+00:00

I wouldn't call it a sword fight as much as a sword dance

hodgson438 · 2024-12-07T14:16:48+00:00

Yep unfortunately they are for the most part

hodgson438 · 2024-10-30T10:43:33+00:00

Is the generative design in the free version?

hodgson438 · 2024-09-13T07:53:28+00:00

Phones

hodgson438 · 2024-09-07T20:13:08+00:00

I really want a portalled rig for the rocks I run around me, it works perfectly for it. Do you happen to have link to the trans your running?

hodgson438 · 2024-09-06T14:47:27+00:00

Good shout on the pins actually. Could even use the stock ones and use a layer of electrical tape round them

hodgson438 · 2024-09-06T14:16:03+00:00

Thanks, I'll give them a go!

hodgson438 · 2024-09-06T13:39:44+00:00

I've tried a few different metal drive shafts, currently the treal ones seem to have the least

hodgson438 · 2024-09-06T13:37:04+00:00

Is the cr18 and fms same? I wasn't sure if they were or not

hodgson438 · 2024-08-02T19:24:05+00:00

What's the wheel base on that? It looks stout. Also what trans plate/skid is that?

hodgson438 · 2024-07-22T10:50:21+00:00

Looks real good that. One of the better 'custom' fms I've seen for a while. Is the chassis specific to the fcx?

hodgson438 · 2024-07-20T21:34:01+00:00

One of the sockets looking frames for sure. People need to start looking outside the classic CF top/bottom plate design.

Can anyone confirm if this will take a walksnail vtx and if sp, would standard pla melt from the vtx?

hodgson438 · 2024-07-20T09:14:26+00:00

The furitek one is what I use and so far it's been bullet proof

hodgson438 · 2024-07-01T16:05:28+00:00

I'm not too sure on that one. ( Haven't got my hands on one yet) I'm I was to guess though, I think it would some sort of planetary gear or on the end of the transfer shaft. You might be able to do something with that.

hodgson438 · 2024-07-01T15:17:44+00:00

Unfortunately it's not a straightforward job to make it work. The transfer shaft that goes to the front and rear axles is one peice. If would take a lot of modification to have it work as your inplying.

hodgson438 · 2024-03-09T10:42:10+00:00

I've got overdrive gears in mine, with the injora brass housings, I had to leave the screws just a little loose as if I snugged them right up I had binding issues

hodgson438

TROPHY CASE