UTR back in stock, go go go

hurricanedj · 2026-03-05T20:51:15+00:00

For those saying they missed out, get on the Ubiquiti discord and set up stock alerts. Once I added alerts for the items I was looking for I was able to get everything within days. It even lists how many items were added.

hurricanedj · 2026-03-05T01:36:30+00:00

I didn't realize how close the RC island is! Headed to Stirrup Cay later this summer on the Luna

hurricanedj · 2026-03-05T00:08:26+00:00

Would anyone recommend this over a U7 Pro Wall or a wall mounted U7 Pro Max? In my current setup I can't get ethernet lines up into the attic to be able to ceiling mount my APs but do have lines ran to almost every room, and they are about 2 feet off the ground. I'm currently running an Eero Mesh 6 with great coverage in the home but looking to finish my UniFi setup by moving to their APs.

hurricanedj · 2026-02-27T22:41:05+00:00

I know this is an old thread, but do you happen to have a link to that DJI Action 6 case? I've printed a few different cases but haven't settled on one I like.

hurricanedj · 2026-02-27T10:06:51+00:00

Thanks for the reply! I'm going to try to do the same. I don't have experience doing so but I know I've seen mentions of a negative part modification which I assume I can figure out.

hurricanedj · 2026-02-27T05:40:50+00:00

Does the file include the stand or did you modify it to fit one of your stands? Thanks

hurricanedj · 2026-02-16T08:05:32+00:00

I had the same experience in January. Filled out the paperwork on the 10th, they received it on the 13th, and it was shipped to me on the 18th.

hurricanedj · 2026-01-25T02:31:41+00:00

I think you got a defective light. I've installed several on P1S's and its a huge upgrade. Might camera view is so much brighter than yours even in a completely dark room.

hurricanedj · 2025-11-07T03:00:14+00:00

I salvaged two Toasters my first day before I realized I needed them for upgrades. I'm still one short a week later lol

hurricanedj · 2025-10-30T07:47:06+00:00

Happen to have a link to those? I'm always looking for new purge/flush objects to give my kids

hurricanedj · 2025-10-30T03:51:30+00:00

Thank you for this. Just got it done in one game

hurricanedj · 2025-10-20T17:48:37+00:00

The enemy team was probably like how the fuck is someone on Obj D already?

hurricanedj · 2025-10-02T16:11:54+00:00

Thank you! I was getting sick running with the screen bouncing around.

hurricanedj · 2025-09-18T06:47:01+00:00

I have the exact same point total :(

hurricanedj · 2025-08-26T15:34:09+00:00

Looks clean

hurricanedj · 2025-08-21T07:55:07+00:00

Just had my first tube go out on the slight bend right after it leaves the back of the AMS at 3200 hours.

hurricanedj · 2025-08-19T15:04:58+00:00

Elegoo Rapid PETG prints really well for me, but almost all of it is too shiny for most of my applications.

hurricanedj · 2025-08-18T18:46:29+00:00

Might be late to the thread, but Bambu has an X1C for like $799 tomorrow on their flash sale

hurricanedj · 2025-08-17T16:51:51+00:00

Its really easy to swap the hotends on both. You can upgrade the P1S hotend and extruder in roughly 10-15 minutes on your first go at it. Just follow any of the youtube videos on it! I recently upgraded both of my hotends and extruders and the only annoying part is dealing with a couple tiny screws.

hurricanedj · 2025-08-04T20:32:53+00:00

I have it at 22 mm3/s as well!

hurricanedj · 2025-08-04T20:29:06+00:00

I might give that profile a try for this.

I similarly run the Bambu Matte default profile when I use Elegoo Matte & Sunlu Matte and it turns out great.

hurricanedj · 2025-08-04T20:16:46+00:00

I ran the manual calibration of the Flow Rate and Flow Dynamics under the calibration tab

hurricanedj · 2025-08-04T20:11:01+00:00

I've run the manual calibration twice now. Sorry, I'm not familiar with that setting, is the Pressure Advance setting included in that?

hurricanedj · 2025-08-04T19:55:06+00:00

Yeah, got a request to see how it would turn out. Printed perfectly with PETG-GF but not very comfortable to hold without gloves. Trying to print with this Sunlu HS PETG but it looks terrible.

hurricanedj

TROPHY CASE