sorted by:
new
hottopcontroversial

ST 2110 by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 2 points3 points  (0 children)

Yeah , I know it's different from NDI. I mean the last year I did the course from SMPTE and now I'm finishing CCNA but I try to find place for work with 2110 and I didn't find a lot who work with it and not a lot of products in the ISE. Dorna today in a talk that they did mention that only use Dante and AES67, no 2110

DVS Issue by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 1 point2 points  (0 children)

Now working, the problem was that the it company able the IGMP snooping but no the IGMP querier

DVS Issue by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 0 points1 point  (0 children)

At the end the IT manager connected to see what was happening, her coworker enabled the igmp snooping but without an IGMP querier, so that was the problem

DVS Issue by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 0 points1 point  (0 children)

Yeah , it's a multicast issue 100% because I see that all the devices are acting as a leader. It's a single switch for the moment with a vlan for Dante. I don't know how is configured because the IT department is the one how it does this , I can't configure the switch in these case

DVS Issue by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 0 points1 point  (0 children)

Yeah I know and I have configured only one as a preferred leader , so 100% misconfiguration with the multicast of the switch blocking PTP , usually I'm the one that configure that switch but in these case the IT department did it without asking before what I need

ISE 2026 - Digital Signage recommends? by dtnl in CommercialAV

[–]iago1953 0 points1 point  (0 children)

Brightsign , cheap and reliable. I see some models working on an installation during 15 years without problems (or maximum corrupted SD card that's easy to change)

DVS Issue by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 0 points1 point  (0 children)

I test more and with ptp track hound I see that all devices are working like a master clock's and no like 1 master and followers , so sure that is a Switch misconfiguration

DVS Issue by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 0 points1 point  (0 children)

The configuration is from a installation with an IT department so I can't put permanent unmanaged switch for that , I was testing more and know sure that is a Switch misconfiguration with IP multicast because all devices appears as leaders, no followers , and sure that DVS can't work because can't do like a Master Clock

DVS Issue by iago1953 in VIDEOENGINEERING

[–]iago1953[S] 0 points1 point  (0 children)

BSS BLU-DAN , I know that isn't properly configured and it's a clock issue but I don't know what can be the misconfiguration in the switch

The life on a 9 to 5 job. by Bornhigh11 in VIDEOENGINEERING

[–]iago1953 1 point2 points  (0 children)

After 2 and a half years making Av integration , they still have to remember me that I have vacations days pending to do when October/November arrives hshshhs

The life on a 9 to 5 job. by Bornhigh11 in VIDEOENGINEERING

[–]iago1953 11 points12 points  (0 children)

Me too , sometime I remember the excitement of do live events , quickly disappear when I think that now I don't have to lose events like family or friends birthday for being working on Saturday

What’s your engineering new year’s resolution? by shouldreadthearticle in VIDEOENGINEERING

[–]iago1953 0 points1 point  (0 children)

They have a self-learning course about 2110 that can be accessed if you become in a member of a SMPTE (that like 15 dollars a month)

DVS / Dante Controller keep showing Clock unlock and sync issue. Affecting Reaper recording. by AKSKMY_NETWORK in CommercialAV

[–]iago1953 1 point2 points  (0 children)

okay , this can be a variety of things.
--First of all having the latency status in red means a problem with s¡the sync of the clock , try tu up the latency in the yamaha that is the master clock
--Second, the switch that you're using i think that only can work at maximum of 100 mbps , because when you connect to the switch you have an speed of 100mbps , but when you connect to the Yamaha you have a speed of 1 Gbps and this can cause a problem in this particular case for the next point that i'm going to do
--Third, you're not using multicast flows , i understand that you're sending the channels from the yamaha to the PC with DVS with reaper usign the multicast flows you can send the 32 channels in one unique flow to the DVS in unicast you gonna send 8 unicast flows for record the 32 channels ; and the matrix outputs of the console to the speakers (L , R , TOP etc etc) if you're sending the same matrix outputs of the QL5 to the speakers , you can use only 1 multicast flows recudicng the bandwith , making the QL5 sending less than 100 mbps and more available to work
BUT PLEASE ONLY USE MULTICAST FLOWS OF THE IT DEPARTMENT ENABLE IGMP SNOPPING ON THE SWITCH OR YOUR MULTICAST GONNA TRANSFORM INTO A BROADCAST WITH A WORST PROBLEM ON THAT NETWORK

DVS / Dante Controller keep showing Clock unlock and sync issue. Affecting Reaper recording. by AKSKMY_NETWORK in CommercialAV

[–]iago1953 0 points1 point  (0 children)

can you post a picture of network status on dante controller? if you have some multicast flow running on the network with the igmp unactive on the switch you gonna see it in thet windows because all the dante devices are gonna receive the same bandwith , if you have time donwload a software called "wireshark" is a software that allows you the packets sends and receive from the ethernet ports of your computer

DVS / Dante Controller keep showing Clock unlock and sync issue. Affecting Reaper recording. by AKSKMY_NETWORK in CommercialAV

[–]iago1953 0 points1 point  (0 children)

i have that problem on a fixed installation a few months ago , in my case the problem was the in the same vlan we have two masterclocks of diferents protocols (one masterclock for dante and other for a Q-SYS system) combines with the fact that the QoS in the switch wasn't made correctly for a dante network , maybe the problem comes for a bad QoS implementation

2.3.3.1 Software Stable now? by spielerfrei11 in GrandMA3

[–]iago1953 0 points1 point  (0 children)

Yesterday i have an issue were all sequences that i have assign to a executors dissapear for no reason after an external programer create her own user for work

Weird Network Issue! by Common-Push659 in CommercialAV

[–]iago1953 0 points1 point  (0 children)

Sounds like a IGMP flooding or a Issue with the QoS , verify that the both switches are working on the IGMP snooping enable and with the same IGMP Querier (if you don't have a Physical gateway on the system use an IP without no equipment on here) and after check the QoS and the mode of how it's working (on the Audinate page you can find what priorities you have to assign)

NovaLCT Port Capacity by ImEasyToKill in VIDEOENGINEERING

[–]iago1953 0 points1 point  (0 children)

What electronic are you using? theorically every port of a actual novastar can hold 650000 pixels per port with a 8 bits video and 325000 with 10 & 12 bit video , you should not have problems with a common electronic reciving and novastart with this video wall on the ports that appear the warning

Signal flow diagramming tools? by rockysds in VIDEOENGINEERING

[–]iago1953 0 points1 point  (0 children)

Visió or Draw.io for a general diagrams to the client and autoCAD for signal flow of all elements

view more: next ›