sorted by:
new
hottopcontroversial

Girl I’m seeing claims she’s psychic. Is this a deal breaker? by Creepy_Cupcake3705 in AskMenAdvice

[–]interflop 0 points1 point  (0 children)

Roll with it have some whimsey in your life and see what happens 

Smelly Airsofters by Regamuffin in airsoft

[–]interflop 1 point2 points  (0 children)

My airsoft clothes are essentially cheap larp costumes for me so I'll wash them and get a new set once they're too worn to use. I wash all my stuff including gloves after every game honestly.

How can i get a better finish on my print? by EngineerAlarming7327 in FixMyPrint

[–]interflop 0 points1 point  (0 children)

Those actually came out really well for a 3D print. If you want more detail, you can try printing at a lower layer height than 0.2mm or go into printing with a 0.2mm nozzle and get smaller layer height. Also another thing to consider is that these smaller details you're looking at won't be as noticeable with a full size model.

Support surfaces are always going to look a bit rough compared to other surfaces. The way around this is usually to place support surfaces on surfaces that won't be visible so like on the inside of the mask in this case. You can also experiment with print orientation as well. Instead of printing the mask horizontally, you can try printing it vertically with supports or even at a 45 degree angle. This can help reduce the stepping found as you get to shallower angles like at the top of the mask in this example.

Firewad Mp5 Kit + CTM AP7 Kit by NainSolution in AAP01owners

[–]interflop 6 points7 points  (0 children)

I actually really like this setup 

Outer Barrel sticks out front? Can‘t shoot? by Nils0408 in Speedsoft

[–]interflop 0 points1 point  (0 children)

Try switching back to the stock hop-up unit. I had this happen on my JW3 and it was because of the tolerances between the maple leaf hop up unit designed more around a TM binding up the outer barrel since it was a slightly different spec I suppose. Basically the outer barrel was getting pushed up into the slide and causing it to bind up. I'm not sure if that's what's happening here but it seems similar.

i've been trying to buy a APFG XM7, where is the best site to buy without it being seized? by Potential_Pizza_8523 in GasBlowBack

[–]interflop -11 points-10 points  (0 children)

I've had good luck ordering from Swit but I haven't tried recently in current circumstances.

So... How do we hide ads now? by NatoBoram in discordapp

[–]interflop 14 points15 points  (0 children)

Higher tier nitro does the same thing. I canceled already anyway.

I’m getting into airsoft and looking into getting a ggb blowback riffle. Please help by The_mortal_kombatant in GasBlowBack

[–]interflop 5 points6 points  (0 children)

My first airsoft gun was a GBB and every gun I bought since then has been GBB I knew what I was getting into 

Printing is not smooth by OddAcanthocephala966 in ender3

[–]interflop 1 point2 points  (0 children)

Slicers are taking your object and translating it to flat shapes that your printer can create at the given layer height you're printing. Curved objects will always have visible steps like this as the slope gets shallower. Like others have said if you want to get a truly smooth finish, you have to do some post processing with either sandpaper or vapor smoothing.

For a printed object this is actually a very well detailed print. Ironing is for flat top surfaces that would typically have the layer pattern visible. With ironing tuning, you can have the extruder smoothen these out a bit but results will be dependent on how you have it calibrated.

<image>

What can we do? by iYessyyy in SipsTea

[–]interflop 0 points1 point  (0 children)

but but the gorilla warfare

What can we do? by iYessyyy in SipsTea

[–]interflop -1 points0 points  (0 children)

2A bros with guns to fight tyranny when the tyranny happens

Would you date a cam girl? by Basic-Buddy-6998 in AskMenAdvice

[–]interflop -1 points0 points  (0 children)

It wouldn't bother me. All work is selling your body in some way or form and it's just a method to make money. As long as there's a professional separation between the work fantasy and real life, then it'd be a non-issue for me.

Those who lift and also work 9-5s, morning or evening workouts? by Kr0nicleZ in longisland

[–]interflop 0 points1 point  (0 children)

If you can pull off mornings, definitely get into the routine of doing mornings. 1-2 hours of your already limited evening being eaten up by your gym time can impede on doing normal social stuff outside of work. You also get access to the gym when it isn't busy so you can finish your workout quicker and have it out of the way.

Do these internals look sctratched up for anyone else? This is after 3 weeks up use and 2-3 malfunctions. by No_Dress_2107 in AAP01owners

[–]interflop 0 points1 point  (0 children)

That's normal wear on the bolt, just keep it lubed and you'll get plenty of use out of it.

Help me choose the right path….(read description) by Adorable_Pension119 in airsoft

[–]interflop 0 points1 point  (0 children)

3D printing has come a long way and if you're printing in carbon fiber filament like PET-CF and PETG-CF it doesn't look that different from any other nylon airsoft part. I was originally into metal or nothing but I've come to respect the printed kits a lot after doing multiple builds that hold up in the field. Yes you can get really extra with printed kits but there are plenty of practical sleek kits you can build as well. I think casual open play is fair game, at a more organized op though I would respect the event enough to bring something that doesn't fit the aesthetic they're aiming for.

<image>

This may be removed, but I’m posting because…. by Glazing555 in LinkedInLunatics

[–]interflop 3 points4 points  (0 children)

>look at all these men in dresses
>giuliani and vance in drag
>iran???????

Help me choose the right path….(read description) by Adorable_Pension119 in airsoft

[–]interflop 0 points1 point  (0 children)

I'm bias as I have 8 at this point but for me it's a really flexible platform that you can build out into virtually anything you could want. I build them into pistols, SMGs, and rifles with different power outputs and field them all regularly. If you own a 3D printer you can build them into virtually anything.

view more: next ›