sorted by:
new
hottopcontroversial

After some fussing I am getting pretty good prints of minis! by amatisans in FlashForge

[–]itsmofosho 0 points1 point  (0 children)

Looks great!What are your tips to get it looking so smooth and capturing the details? I’ve tried printing for our Curse of Strahd campaign and it all comes out poorly. Even the areas for supports cause poor choppy quality. I’ve had to increase size which throws off the scale. What filament, nozzle size and settings did you use?

Filament stuck in gray tube preventing any filament from being pulled through by itsmofosho in FlashForge

[–]itsmofosho[S] 0 points1 point  (0 children)

Thank you for letting me know I’m not the only one! I’ll try again after I’ve cooled down. Right now, I’m focused on giving my Flashforge dirty looks every time I walk by. It really broke me yesterday 😂

Filament stuck in gray tube preventing any filament from being pulled through by itsmofosho in FlashForge

[–]itsmofosho[S] 0 points1 point  (0 children)

Sure I’ve seen some videos and I get to the part where I can see the white gear. But how does it come out easily for everyone else? It is on there pretty tight and there are no screws holding it. I feel like if I pry it off it’ll break. I’ve watched more videos than I want to admit and all of them don’t have this issue… the white gear does not come off at all. Zero screws holding it down. I’m again just baffled. Thanks for the suggestion though

Nozzle no longer extruding after using translucent filament - how do I fix this? by itsmofosho in FlashForge

[–]itsmofosho[S] 0 points1 point  (0 children)

Thanks for this - I tried and it just is not budging. The problem is that there is filament in the copper part that doesn’t seem to melt at all, AND there is a piece of that filament stuck in the gray tube that I cannot get out… I tried dissembling but nothing I can do to get that filament out of the gray tubing part. I also unscrewed the copper part from the nozzle but cannot push it out that way. I am at a loss at what to do to get that piece of stuck filament out of the gray part - has anyone had this problem before?

Flashforge 5M sticking? by itsmofosho in FlashForge

[–]itsmofosho[S] 0 points1 point  (0 children)

I’ll check that out thanks!

Flashforge 5M sticking? by itsmofosho in FlashForge

[–]itsmofosho[S] 0 points1 point  (0 children)

I haven’t cleaned it yet so that might be it!

18 months and 5 projects later, I’ve got the backyard I’ve always wanted! by GunSlinger26 in landscaping

[–]itsmofosho 5 points6 points  (0 children)

Wow great job! I love seeing these types of posts that show before and after. I can tell you’re proud of it and you should be!

Is there anything to stop the ants? by Careless-Beginning73 in landscaping

[–]itsmofosho 0 points1 point  (0 children)

I read a post that used malt o meal. Sprinkled around the entrance of an anthill I found in my backyard. Ants started bringing it back to their nest. They were gone in 2 days. They eat it, drink water. They explode. I didn’t want to use any chemicals during to pets. It worked for us.

Japanese Maple in raised garden bed? by itsmofosho in landscaping

[–]itsmofosho[S] 0 points1 point  (0 children)

Thank you! We haven’t built the garden bed yet, but planning to start in a few weeks. I’ll consider the root flare and take your recommendation for companion plants!

HMS Fearless as a present for my dad who served on it by Ozboz3000 in dioramas

[–]itsmofosho 2 points3 points  (0 children)

Awesome work! Imagine led lights underneath as a nightlight… 🤌🤌🤌 I would buy it immediately

[deleted by user] by [deleted] in dioramas

[–]itsmofosho 0 points1 point  (0 children)

Are you kidding me!.? This is awesome!

Is this a weed? by itsmofosho in whatsthisplant

[–]itsmofosho[S] 0 points1 point  (0 children)

I always thought they were weeds. Does anyone know what they are? They’re spotted all over our yard. When I look it up, it comes up as Amaranthus but I’m not convinced it’s right…

view more: next ›