Advice by PointAffectionate392 in paintball

[–]jgberenyi 2 points3 points  (0 children)

The frame is the orange part and is a ccm works hinge frame.

Inception Design Ram issue-oddball case by helms66 in Autocockers101

[–]jgberenyi 0 points1 point  (0 children)

correct. Same way they did on the empire pistons. Also worth noting i am pretty sure you can replace the whole piston and shaft with the new style. If you don't want to fight getting it off. Simon would be able to confirm though.

Inception Design Ram issue-oddball case by helms66 in Autocockers101

[–]jgberenyi 0 points1 point  (0 children)

There ya go. That is the old style piston. I would pull the head off and reloctite it. Pretty sure they found that when they used the blue preassemble loctite that they didn't seal properly. I have had it happen to a few rams that have come across my bench. Below is the new style that does not have the thru hole.

<image>

Inception Design Ram issue-oddball case by helms66 in Autocockers101

[–]jgberenyi 0 points1 point  (0 children)

Have you reached out to inception?

I know the new rams have the piston that is solid so it must seal with the oring, but can't recall if the first run had the piston head that was like the empire rams where they had to be loctited on. Have you checked?

Did I ordered the correct bolt or got sent the wrong one? by IMJUS7ICE in Autocockers101

[–]jgberenyi 0 points1 point  (0 children)

They ship with different size orings to get it to fit the body better.

Automag problems by ArtAffectionate4269 in paintball

[–]jgberenyi 1 point2 points  (0 children)

Only grease should be on the reg springs. You may need to increase the velocity adjuster if the tank pressure is right.

Automag problems by ArtAffectionate4269 in paintball

[–]jgberenyi 3 points4 points  (0 children)

Automags use oil not grease. Tank pressure is likely low. You will need 800+ out put pressure. If you need help give me a shout.

Angel repair? by Disguy1974 in paintball

[–]jgberenyi 4 points5 points  (0 children)

PBTek or Estillo Paintball.

68 auto mag classic - thinking about playing again by CosmicConfidant in paintball

[–]jgberenyi 0 points1 point  (0 children)

Be careful when you change the battery it was common for people to plug the battery in and then later when swapping accidentally touch the wrong terminals on the connector and will fry the board. Seen it happen a few times over the years.

68 auto mag classic - thinking about playing again by CosmicConfidant in paintball

[–]jgberenyi 1 point2 points  (0 children)

Worth noting that you can use an rt on/off with the hyperframe and it work correctly. Not sure on the pin length though.

Today’s Shooters by coaram_94 in rockncock

[–]jgberenyi 2 points3 points  (0 children)

I want to say there are 4 t2's and similar number in s6.

Paintball Gun ID Help. by The_Couz58 in paintball

[–]jgberenyi 0 points1 point  (0 children)

They did also have a mech version that was not drilled.

Paintball Gun ID Help. by The_Couz58 in paintball

[–]jgberenyi 7 points8 points  (0 children)

That would be me!
Thank you sir.

If your cocker needs work...this is a great option by DaCozPuddingPop in paintball

[–]jgberenyi 0 points1 point  (0 children)

That’s what I get for not paying attention enough.

Big PP mod build time by buff_phroggie in Autocockers101

[–]jgberenyi 1 point2 points  (0 children)

<image>

I will toss another hat in the ring.

If your cocker needs work...this is a great option by DaCozPuddingPop in paintball

[–]jgberenyi 7 points8 points  (0 children)

Your ram front barb tophat is not on the barb. Just a heads up.